Ford 2011 Escape v.2 Manual de usuario

Introduction 4Instrument Cluster 12Warning lights and chimes 12Gauges 17Message center 20Entertainment Systems 29AM/FM stereo with CD/MP3 29Auxiliary

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Airbag - FrontAirbag

1. Place the key in the ignition andturn the ignition to the on position.2. Press the power door unlockcontrol on the door panel threetimes.3. Turn th

CHILDPROOF DOOR LOCKSWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thechi

The IKT allows you to:• remotely unlock the vehicledoors.• remotely lock all the vehicledoors.• remotely open the power liftgateglass.• activate the p

Locking the doors1. Pressand release to lock all the doors. Assuming all vehicle doorsand the liftgate are properly closed, the parking lamps will ill

To replace the battery:1. Twist a thin coin in the slot of theIKT near the key ring in order toremove the battery cover.Note: Do not wipe off any grea

The illuminated entry system will turn off the lights if:• the ignition is turned to the on position, or• the integrated keyhead transmitter lock cont

Programming your own personal entry codeTo create your own personal entry code:1. Enter the factory set code.2. Within five seconds press the 1 • 2 on

• pressing the control on the remote entry transmitter,• or the ignition position changes.Unlocking and locking the doors and liftgate using keyless e

Note: Do not leave a duplicate coded key in the vehicle. Alwaystake your keys and lock all doors when leaving the vehicle.Anti-theft indicatorThe anti

key that operates all the locks and starts the vehicle, as well as a remotekeyless entry transmitter. A maximum of eight coded keys can beprogrammed t

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleasePanic Alarm Engine Oi

Please read and understand theentire procedure before you begin.1. Insert the first previouslyprogrammed coded key into theignition.2. Turn the igniti

FRONT SEATSWARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the eve

To adjust the head restraint, do the following:1. Adjust the seatback to an upright driving/riding position.2. Raise the head restraint bypulling up o

To remove the adjustable head restraint, do the following:1. Pull up the head restraint until itreaches the highest adjustmentposition.2. Simultaneous

WARNING: To minimize the risk of neck injury in the event of acrash, head restraints must be installed properly.Adjusting the front manual seat (if eq

WARNING: Reclining the seatback can cause an occupant toslide under the seat’s safety belt, resulting in severe personalinjuries in the event of a col

Press the control to move the seatforward, backward, up or down.Heated seats (if equipped)WARNING: Persons who are unable to feel pain to the skinbeca

REAR SEATSSecond row adjustable head restraintsYour vehicle is equipped with second row outboard and center headrestraints that are vertically adjusta

3. Lower the head restraint bypressing and holding the guidesleeve adjust/remove button andpushing down on the head restraint.Properly adjust the head

2. Press and hold the adjust/removebutton, then pull up on the headrestraint.To reinstall the adjustable head restraint, do the following:1. Insert th

WARNING LIGHTS AND CHIMESBase instrument cluster shown in standard measure. Metricsimilar.Optional instrument cluster shown in standard measure. Metri

2. Pull the seat release strap.Note: Make sure the floor is clear of all objects before folding the seat.3. Flip seat forward.Attach the safety belt w

4. To release seatback, pull theseatback release lever (on top ofseat) toward the front seat. This iscommon for both 60% and 40%seatbacks.Note: When t

2. Rotate seat cushion down into theseating position making sure thatthe seat cushion is locked into placeand that the safety belt buckles areexposed.

To install the second row cushion1. Push the cushion to the inboardside of the vehicle.2. Make sure that the hinges arelocked into place.SAFETY RESTRA

How does the Personal Safety System™ work?The Personal Safety System can adapt the deployment strategy of yourvehicle’s safety devices according to cr

Front passenger sensing systemFor airbags to do their job they must inflate with great force, and thisforce can pose a potentially deadly risk to occu

Front safety belt pretensionersThe safety belt pretensioners at the front outboard seating positions aredesigned to tighten the safety belts firmly ag

Safety restraints precautionsWARNING: Always drive and ride with your seatback uprightand the lap belt snug and low across the hips.WARNING: To reduce

WARNING: Safety belts and seats can become hot in a vehiclethat has been closed up in sunny weather; they could burn asmall child. Check seat covers a

Pregnant women should alwayswear their safety belt. The lap beltportion of a combination lap andshoulder belt should be positionedlow across the hips

Many lights will illuminate when you start your vehicle to make sure thebulbs work. If any light remains on after starting the vehicle, refer to there

When to use the automatic locking modeThis mode should be used any time a child safety seat, except abooster, is installed in passenger front or rear

Safety belt height adjustmentYour vehicle has safety belt heightadjustments at the front outboardseating positions. Adjust the heightof the shoulder b

numbers 611C22–A and 611C22–B respectively). These assemblies canbe obtained from an authorized dealer.Use only extensions manufactured by the same su

Belt-Minder威 feature for objects placed in the front passenger seat,warnings will only be given to large front seat occupants as determinedby the fron

The following are reasons most often given for not wearing safety belts(All statistics based on U.S. data):Reasons given... Consider...⬙Crashes are ra

Reasons given... Consider...⬙The people I’m with don’twear belts⬙Set the example, teen deaths occur 4times more often in vehicles withTWO or MORE peop

• The gearshift is in N (Neutral) (manual transmission)• The ignition switch is in the off position• The driver and front passenger safety belts are u

AIRBAG SUPPLEMENTAL RESTRAINT SYSTEM (SRS)Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right

WARNING: Never place your arm over the airbag module as adeploying airbag can result in serious arm fractures or otherinjuries.To properly position yo

Children and airbagsChildren must always be properlyrestrained. Accident statisticssuggest that children are safer whenproperly restrained in the rear

Brake system warning light: Toconfirm the brake system warninglight is functional, it willmomentarily illuminate when theignition is turned to the on

The airbags inflate and deflaterapidly upon activation. After airbagdeployment, it is normal to notice asmoke-like, powdery residue orsmell the burnt

The RCM (restraints control module) monitors its own internal circuitsand the supplemental airbag electrical system wiring (including theimpact sensor

The front passenger sensing systemuses a ⬙passenger airbag off⬙ or⬙pass airbag off⬙ indicator which willilluminate and stay lit to remind youthat the

• If the indicator lamp remains lit even after this, the person should beadvised to ride in the rear seat.OccupantPass Airbag OffIndicator LampPasseng

ObjectsPass Airbag OffIndicator LampPassenger AirbagSmall (i.e. three-ringbinder, small purse,bottled water)Unlit DisabledMedium (i.e. heavybriefcase,

In case there is a problem with thefront passenger sensing system, theairbag readiness lamp in theinstrument cluster will stay lit.If the airbag readi

A difficulty with the system is indicated by one or more of the following:• The readiness light will eitherflash or stay lit.• The readiness light wil

How does the side airbag system work?The design and development of theside airbag system includedrecommended testing proceduresthat were developed by

WARNING: Several airbag system components get hot afterinflation. Do not touch them after inflation.WARNING: If the sideairbag has deployed, theairbag

Safety Canopy姞 SystemWARNING: Do not placeobjects or mount equipmenton or near the headliner at thesiderail that may come intocontact with a deploying

Charging system: Illuminates whenthe battery is not charging properly.If it stays on while the engine isrunning, there may be a malfunctionwith the ch

How does the Safety Canopy姞 System work?The design and development of theSafety Canopy system includedrecommended testing proceduresthat were develope

The Safety Canopy is mounted to roof side-rail sheet metal, behind theheadliner, above the first and second row seats. The Safety Canopy isdesigned to

A difficulty with the system is indicated by one or more of the following:• The readiness light (same light as for front airbag system) will eitherfla

SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Airbag suppleme

Recommendations for Safety Restraints for ChildrenChild size, height, weight, or ageRecommendedrestraint typeInfants ortoddlersChildren weighing 40 lb

• When possible, always properly restrain children twelve (12) years ofage and under in a rear seating position of your vehicle. Accidentstatistics su

WARNING: Always carefully follow the instructions andwarnings provided by the manufacturer of any child restraint todetermine if the restraint device

training to ensure that all children ages 0 to 16 are properly restrained inthe correct restraint system. Ford recommends checking with a NHTSACertifi

Airbags can kill or injure a child in a child seat. NEVER place arear-facing child seat in front of an active airbag. If you must use aforward-facing

Perform the following steps when installing the child seat withcombination lap/shoulder belts:Note: Although the child seat illustrated is a forward f

Speed control: Illuminates whenthe speed control is engaged. Turnsoff when the speed control systemis disengaged.Overdrive cancel and gradeassist: Ill

3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi

8. Remove remaining slack from thebelt. Force the seat down with extraweight, e.g., by pressing down orkneeling on the child restraint whilepulling up

method eliminates the need to use safety belts to attach the child seat,however the safety belt can still be used to attach the child seat. Forforward

Use of inboard lower anchors from the outboard seating positions(center seating use)The lower anchors at the center of the second row rear seat are sp

The rear seating positions of your vehicle are equipped with built-intether strap anchors located behind the seats on the roof panel in thecargo area.

2. Locate the correct anchor for theselected seating position.There are three tether anchorslocated on the headliner at the rearof the vehicle.3. Clip

around four (4) years of age. Consult your child safety seat owner guidefor the weight, height, and age limits specific to your child safety seat.Keep

• Is the shoulder belt centered on the shoulder and chest?• Can the child stay seated like this for the whole trip?Types of booster seatsThere are gen

Children and booster seats vary in size and shape. Choose a booster thatkeeps the lap belt low and snug across the hips, never up across thestomach, a

Follow all instructions provided by the manufacturer of the booster seat.WARNING: Never place, or allow a child to place, the shoulderbelt under a chi

Parking brake on chime: Sounds when the parking brake is left on andthe vehicle is driven. If the warning stays on after the park brake is off,contact

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERSUtility vehicles and trucks handledifferently than passenger cars inthe various driving conditions thatare e

For 4WD vehicles, a spare tire of a different size other than the tireprovided should never be used. A dissimilar spare tire size (other thanthe spare

• Narrower – to provide greatermaneuverability in tight spaces,particularly in off-road use.As a result of the above dimensionaldifferences, SUVs and

TreadwearThe treadwear grade is a comparative rating based on the wear rate ofthe tire when tested under controlled conditions on a specifiedgovernmen

TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary

INFLATING YOUR TIRESSafe operation of your vehicle requires that your tires are properlyinflated. Remember that a tire can lose up to half of its air

The cold inflation pressure should never be set lower than therecommended pressure on the Safety Compliance Certification Label orTire Label.When weat

TIRE CAREInspecting your tires and wheel valve stemsPeriodically inspect the tire treads for uneven or excessive wear andremove objects such as stones

WARNING: AgeTires degrade over time depending on many factors such asweather, storage conditions, and conditions of use (load, speed,inflation pressur

WARNING: Only use replacement tires and wheels that are thesame size, load index, speed rating and type (such as P-metricversus LT-metric or all-seaso

Optional instrument cluster shown in standard measure. Metricsimilar.Speedometer: Indicates thecurrent vehicle speed.Engine coolant temperaturegauge:

It is recommended that the two front tires or two rear tires generally bereplaced as a pair.The tire pressure sensors mounted in the wheels (originall

vehicle seems to pull to one side when you’re driving, the wheels may beout of alignment. Have an authorized dealer check the wheel alignmentperiodica

Note: Your vehicle may be equipped with a dissimilar spare tire/wheel. Adissimilar spare tire/wheel is defined as a spare tire and/or wheel that isdif

5. 15: Indicates the wheel or rim diameter in inches. If you change yourwheel size, you will have to purchase new tires to match the new wheeldiameter

numbers represent the week and year the tire was built. For example,the numbers 317 mean the 31st week of 1997. After 2000 the numbersgo to four digit

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation beyond those of “P”type tires;

Information on “T” type tires“T” type tires have some additionalinformation beyond those of “P”type tires; these differences aredescribed below:T145/8

TIRE PRESSURE MONITORING SYSTEM (TPMS)Each tire, including the spare (ifprovided), should be checkedmonthly when cold and inflated tothe inflation pre

The tire pressure monitoring system complies with part 15 of the FCCrules and with RSS-210 of Industry Canada. Operation is subject to thefollowing tw

Understanding your tire pressure monitoring system (TPMS)The tire pressure monitoring system measures pressure in your four roadtires and sends the ti

WARNING: Never remove the coolant reservoir cap while theengine is running or hot.Fuel gauge: Indicatesapproximately how much fuel is leftin the fuel

Low tire pressurewarning lightPossible cause Customer action requiredSolid warning light Tire(s)under-inflated1. Check your tire pressure toensure tir

Low tire pressurewarning lightPossible cause Customer action requiredFlashing warninglightSpare tire in use Your temporary spare tire is inuse. Repair

tire is under-inflated, carefully drive the vehicle to the nearest locationwhere air can be added to the tires. Inflate all the tires to therecommende

provide maximum return of vehicle design performance. Before loadingyour vehicle, familiarize yourself with the following terms for determiningyour ve

Example only:Cargo Weight – includes all weight added to the Base Curb Weight,including cargo and optional equipment. When towing, trailer tongue load

GAWR (Gross Axle Weight Rating) – is the maximum allowableweight that can be carried by a single axle (front or rear). Thesenumbers are shown on the S

• Example only:WARNING: Exceeding the Safety Compliance Certification Labelvehicle weight rating limits could result in substandard vehiclehandling or

GCW (Gross Combined Weight) – is the weight of the loaded vehicle(GVW) plus the weight of the fully loaded trailer.GCWR (Gross Combined Weight Rating)

WARNING: Exceeding any vehicle weight rating limitation couldresult in serious damage to the vehicle and/or personal injury.Steps for determining the

to transport the cement to your home? If you and your friend eachweigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12x 100) = 1400

Locks and Security 91Keys 91Locks 97Anti-theft system 107Seating and Safety Restraints 111Seating 111Safety restraints 123Airbags 137Child restraints

Trip odometer: Registers the miles (kilometers) of individual journeys.• Standard instrument cluster:Press the SELECT/RESET controlonce to switch from

Follow these guidelines to ensure safe towing:• Do not tow a trailer until your vehicle has been driven at least1,000 miles (1,600 km).• Consult your

Powertrain Maximum GCWR- lb (kg)1Maximum TrailerWeight - lb (kg)22WD 2.5L w/manualtransmission5000 (2268) 1500 (680)2WD 2.5L w/automatictransmission50

If you use a rental trailer, follow the instructions that the rental agencygives to you.Do not attach safety chains to the bumper.Trailer brakesElectr

• Allow more distance for stopping with a trailer attached; anticipatestops and brake gradually.Trailer towing tips• Practice turning, stopping and ba

In case of roadside emergency with a disabled vehicle, please refer toWrecker towing in the Roadside Emergencies chapter.These guidelines are designed

STARTINGPositions of the ignition1. Off— locks the gearshift leverand allows key removal. Note: Inorder to switch off the engine whilethe vehicle is i

WARNING: Do not start your vehicle in a closed garage or inother enclosed areas. Exhaust fumes can be toxic. Always openthe garage door before you sta

• Make sure the gearshift is in P(Park).If starting a vehicle with a manualtransmission:• Make sure the parking brake isset.• Press and hold the clutc

Some warning lights will briefly illuminate. See Warning lights andchimes in the Instrument Cluster chapter for more informationregarding the warning

Do not crank the engine for more than 10 seconds at a time as starterdamage may occur. If the engine fails to start, turn the key to off andwait 30 se

MILES (km) TO EThis displays an estimate of approximately how far you can drive withthe fuel remaining in your tank under normal driving conditions.Re

the user to connect the system to a grounded 120 volt A/C electricalsource. The block heater system is most effective when outdoortemperatures reach b

• Be sure that the engine block heater, heater cord and extension cordare solidly connected. A poor connection can cause the cord tobecome very hot an

Four-wheel anti-lock brake system (ABS)Your vehicle is equipped with an anti-lock braking system (ABS). Thissystem helps you maintain steering control

Parking brakeApply the parking brake wheneverthe vehicle is parked. To set theparking brake, press the parkingbrake pedal down until the pedalstops.Th

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.ADVANCETR

WARNING: Remember that even advanced technology cannotdefy the laws of physics. It’s always possible to lose control of avehicle due to inappropriate

When AdvanceTrac威 with RSC威 performs a normal system self-check,some drivers may notice a slight movement of the brake, and/or arumble, grunting, or g

or avoiding objects in the roadway. ESC operates by applying brakes toone or more of the wheels individually and, if necessary, reducing enginepower i

can be restored by pressing the traction control off button again, or byturning off and restarting the engine.If you switch off the traction control,

WARNING: Trailer sway control does not prevent a trailer fromswaying, it mitigates the sway from increasing once it hasoccurred. TSC cannot stop all t

Your vehicle must be moving to calculate instantaneous fuel economy.When your vehicle is not moving, this function shows ↓, one or no barsilluminated.

STEERINGYour vehicle is equipped with an electric power-assisted steering (EPAS)system. There is no fluid reservoir to check or fill.If your vehicle l

WARNING: Loaded vehicles, with a higher center of gravity,may handle differently than unloaded vehicles. Do not overloadyour vehicle and use extra pre

2. Using a screwdriver or similartool, carefully pry out the smallBrake Transmission Shift Interlock(BTSI) cover cap located to theright of the gearsh

considered normal and will not affect function or durability of thetransmission. Over time, the adaptive learning process will fully updatetransmissio

N (Neutral)With the gearshift lever in N (Neutral), the vehicle can be started and isfree to roll. Hold the brake pedal down while in this position.D

O/D (overdrive mode) is automatically returned each time the engine isturned off.L (Low)• Provides maximum engine braking.• Will downshift to the lowe

Do not drive with your foot resting on the clutch pedal or use theclutch pedal to hold your vehicle at a standstill while waiting on ahill. These acti

3. Turn the ignition off.WARNING: Do not park your vehicle in Neutral, it may moveunexpectedly and injure someone. Use 1 (First) gear and set theparki

The RSS detects obstacles up to6 feet (1.8 meters) from the rearbumper with a decreased coveragearea at the outer corners of thebumper, (refer to the

REARVIEW CAMERA SYSTEM (IF EQUIPPED)The rearview camera system locatedon the liftgate provides a videoimage, which appears in therearview mirror or on

To reset the oil monitoring system to 100% after each oil change,perform the following:1. Press and release the SETUP button to display “OIL LIFE XXX%

Note: The default setting for the camera delay is off. Press the“Settings” button found on the navigation screen (if equipped) to set thecamera delay

Servicing• If the image comes on while the vehicle is not in R (Reverse), havethe camera inspected by your authorized dealer.• If the image is not cle

For best performance, the driver should drive the vehicle as parallel aspossible while passing a parking space. If driven too fast (above 18 mph[30 km

When you determine the vehicle is back far enough or you hear a solidtone from the reverse sensing system, bring the vehicle to a completestop and mov

• Exceeding a vehicle speed of 6 mph (10 km/h) during automaticsteering• Deactivating the AdvanceTrac威 system or the system has activated ona slippery

Why doesn’t APA position the vehicle where I want in the space?• The driver allows the vehicle to roll in the opposite direction of thetransmission (s

Driving with blind spot mirrorsBefore a lane change, check themain mirror first, then check theblind spot mirror. If no vehicles arepresent in the bli

Driving off-road with truck and utility vehicles4WD vehicles are specially equipped for driving on sand, snow, mud andrough terrain and have operating

sideways out of control or roll over. Remember, your safety and thesafety of others should be your primary concern.WARNING: Vehicles with a higher cen

Emergency maneuvers• In an unavoidable emergency situation where a sudden sharp turnmust be made, remember to avoid “over-driving” your vehicle, i.e.,

ZONE [XX] RESET = CHANGE (if equipped)For more information on the compass and compass set up, refer toElectronic compass in the Driver Controls chapte

Mud and waterIf you must drive through highwater, drive slowly. Traction orbrake capability may be limited.When driving through water,determine the de

slopes or hills. A danger lies in losing traction, slipping sideways andpossibly rolling over. Whenever driving on a hill, determine beforehandthe rou

Avoid sudden applications of power and quick changes of direction onsnow and ice. Apply the accelerator slowly and steadily when startingfrom a full s

Failure to maintain your vehicle properly may void the warranty, increaseyour repair cost, reduce vehicle performance and operational capabilitiesand

ROADSIDE ASSISTANCEGetting roadside assistanceTo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside

Using roadside assistanceComplete the roadside assistance identification card and place it in yourwallet for quick reference. In the United States, th

This switch is located in the frontpassenger’s footwell, behind aflip-up cover, by the kick panelaccess cover.To reset the switch:1. Turn the ignition

Standard fuse amperage rating and colorCOLORFuseratingMinifusesStandardfusesMaxifusesCartridgemaxifusesFuse linkcartridge2A Grey Grey — — —3A Violet V

The fuses are coded as follows:Fuse/RelayLocationFuse AmpRatingProtected Circuits1 30A Not used (spare)2 15A Brake on/off switch3 15A SYNC威 module4 30

Fuse/RelayLocationFuse AmpRatingProtected Circuits15 10A Climate control16 15A Not used (spare)17 20A All lock motor feeds, Liftgaterelease, Liftglass

REAR RIGHT DOOR AJAR — Displayed when the rear right door isnot completely closed.PARK BRAKE ENGAGED — Displayed when the parking brake is set,the eng

Fuse/RelayLocationFuse AmpRatingProtected Circuits41 15A Driver/passenger door lockswitches, Automatic dimmingmirror, Compass, Ambientlighting, Moon r

The high-current fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingProtected CircuitsA 80A Midi Electronic power steering module(EPAS)B 125A

Fuse/RelayLocationFuse AmpRatingProtected Circuits14 15A* Trailer tow turn lamps15 — Not used16 40A** Cooling fan 117 40A** Cooling fan 218 20A** ABS

Fuse/RelayLocationFuse AmpRatingProtected Circuits31F — Liftgate latch relay32 — Not used33 — PCM diode34 — Start diode35 10A* Run/start, Reverse lamp

Dissimilar spare tire/wheel informationWARNING: Failure to follow these guidelines could result in anincreased risk of loss of vehicle control, injury

3. Full-size dissimilar spare without label on wheelWhen driving with the full-size dissimilar spare tire/wheel, do not:• Exceed 70 mph (113 km/h)• Us

Stopping and securing the vehicle1. Park on a level surface, set theparking brake and activate hazardflashers.2. Place gearshift lever in P (Park)(aut

5. Remove the lug wrench from thejack in order to remove the sparetire from under the vehicle.Removing the spare tire or spare tire and tether (if equ

5. Use the lug wrench to remove thelug nut from the spare tire tether.6. If not replacing the spare or flattire to the underbody storage area,raise wi

WARNING: Do not attempt to change a tire on the side of thevehicle close to moving traffic. Pull far enough off the road toavoid the danger of being h

KEY COULD NOT PROGRAM — Displayed when an attempt is madeto program a spare key using two existing MyKeys. Refer to MyKey™ inthe Locks and Security ch

• FrontView shown from rear of front tire.Position the jack directly below theprotruding bolt.• RearView shown from forward of reartire. Position the

3. Position the jack according to theguides and turn the jack handleclockwise until the tire is amaximum of 1 inch (25 mm) off theground.Be sure to pl

7. Remove the jack and fully tightenthe lug nuts in the order shown.Refer to Wheel lug nut torquespecifications later in this chapterfor the proper lu

1. Place tire on end with valve stemfacing rearward, away from vehicle.2. Place tether into bolt holes inwheel and attach lug nut using lugwrench.3. L

WHEEL LUG NUT TORQUE SPECIFICATIONSRetighten the lug nuts to the specified torque at 500 miles (800 km)after any wheel disturbance (tire rotation, cha

the Easy Fuel™ “no cap” fuel system as it can be damaged. You mustuse the included funnel in such circumstances.WARNING: Do not insert the nozzle of p

5. Turn the heater fan on in both vehicles to protect from any electricalsurges. Turn all other accessories off.Connecting the jumper cablesNote: In t

Jump starting1. Start the engine of the booster vehicle and run the engine atmoderately increased speed.2. Start the engine of the disabled vehicle.3.

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

Ford Motor Company produces a towing manual for all authorized towtruck operators. Have your tow truck operator refer to this manual forproper hook-up

CANCELLED BY DRIVER INPUT (if equipped) — Displayed whenthe autopark feature has been canceled due to driver inputs. See Activepark assist in the Driv

GETTING THE SERVICES YOU NEEDWarranty repairs to your vehicle must be performed by an authorizeddealer. While any authorized dealer handling your vehi

In Canada:Mailing address (Ford vehicles)Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E4Teleph

In the United States, a warranty dispute must be submitted to the BBBAUTO LINE before taking action under the Magnuson-Moss WarrantyAct, or to the ext

LINE before exercising rights or seeking remedies created by the FederalMagnuson-Moss Warranty Act, 15 U.S.C. sec. 2301 et seq. If you chooseto seek r

You can get more information by calling BBB AUTO LINE at1-800-955-5100, or writing to:BBB AUTO LINE4200 Wilson Boulevard, Suite 800Arlington, Virginia

The use of leaded fuel in your vehicle without proper conversion maydamage the effectiveness of your emission control system and may causeengine knock

If your vehicle must be serviced while you are traveling or living in theMiddle East, contact the nearest authorized dealer. If the authorizeddealer c

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralpH shampoo, such as Motorcraft威 Detail Wash (ZC-3-A), which i

• Do not allow paint sealant to come in contact with any non-body(low-gloss black) colored trim, such as grained door handles, roofracks, bumpers, sid

ACTIVE PARK NOT AVAILABLE (if equipped) — May display whenusing the active park assist system. See Active park assist in theDriving chapter for more i

• Spray Motorcraft威 Engine Shampoo and Degreaser (ZC-20) on allparts that require cleaning and pressure rinse clean. In Canada, useMotorcraft威 Engine

PLASTIC (NON-PAINTED) EXTERIOR PARTSUse only approved products to clean plastic parts. These products areavailable from your authorized dealer.• For r

INSTRUMENT PANEL/INTERIOR TRIM AND CLUSTER LENSClean the instrument panel, interior trim areas and cluster lens with aclean, damp, white cotton cloth,

INTERIORFor fabric, carpets, cloth seats, safety belts and seats equipped with sideairbags:• Remove dust and loose dirt with a vacuum cleaner.• Remove

• Do not use household cleaning products, alcohol solutions, solvents orcleaners intended for rubber, vinyl and plastics, or oil/petroleum-basedleathe

• Clean the surfaces using the steps outlined in the Cleaning section.• Ensure the leather is dry then apply a nickel-sized amount ofconditioner to a

SERVICE RECOMMENDATIONSTo help you service your vehicle, we provide scheduled maintenanceinformation which makes tracking routine service easy.If your

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under thebottom of the instrument panel.2. At the front of the vehicle, lif

3.0L V6 engine1. Engine coolant reservoir2. Air filter assembly3. Brake fluid reservoir4. Automatic transmission fluid dipstick5. Power distribution b

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

AUDIO SYSTEMSAM/FM single CD/MP3 satellite compatible sound systemWARNING: Driving while distracted can result in loss of vehiclecontrol, accident and

CHANGING THE WIPER BLADES1. Pull the wiper blade and armaway from the glass.2. Squeeze the locking tabs torelease the blade from the arm andpull the b

Changing rear window wiper bladeThe rear wiper arm is designed without a service position. This reducesthe risk of damage to the blade in an automatic

5. Locate and carefully remove the engine oil level dipstick.• 2.5L I4 engine• 3.0L V6 engine6. Wipe the dipstick clean. Insert the dipstick fully, th

• 3.0L V6 engine• If required, add engine oil to the engine. Refer to Adding engine oilin this chapter.• Do not overfill the engine with oil. Oil leve

Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oilOnly use oils certified for gasoline engines by the

BATTERYYour vehicle is equipped with aMotorcraft威 maintenance-freebattery which normally does notrequire additional water during itslife of service.If

WARNING: Keep batteries out of reach of children. Batteriescontain sulfuric acid. Avoid contact with skin, eyes or clothing.Shield your eyes when work

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

• Refer to scheduled maintenance information for service intervalschedules.If the engine coolant has not been checked at the recommended interval,the

• Do not use alcohol, methanol, brine or any engine coolantsmixed with alcohol or methanol antifreeze (coolant). Alcoholand other liquids can cause en

Customer Assistance 270Reporting safety defects (U.S. only) 277Reporting safety defects (Canada only) 277Cleaning 278Maintenance and Specifications 28

AM/FM Radio/ VOL (Power/Volume): Pressto turn the radio on/off. Turn theknob to increase/decrease volume.If the volume is set above a certainlevel and

Whenever coolant has been added, the coolant level in the coolantreservoir should be checked the next few times you drive the vehicle. Ifnecessary, ad

If you drive in extremely hot climates:• It is still necessary to maintain the coolant concentrationabove 40%.• NEVER decrease the coolant concentrati

When fail-safe mode is activatedYou have limited engine power when in the fail-safe mode, so drive thevehicle with caution. The vehicle will not be ab

WARNING: The fuel system may be under pressure. If you heara hissing sound near the fuel filler door (Easy Fuel™ “no cap”fuel system), do not refuel u

• Be particularly careful if you are taking “Antabuse” or other forms ofdisulfiram for the treatment of alcoholism. Breathing gasoline and/orethanol v

WARNING: The flow of fuel through a fuel pump nozzle canproduce static electricity, which can cause a fire if fuel ispumped into an ungrounded fuel co

3. Slowly insert the fuel filler nozzle fully into the fuel system, and leavethe nozzle fully inserted until you are done pumping. Pump fuel asnormal.

If your vehicle is not a flexible fuel vehicle (FFV), then only useUNLEADED fuel or UNLEADED fuel blended with a maximum of 10%ethanol. Do not use fue

Fuel qualityUnleaded gasoline enginesIf you experience starting, rough idle or hesitation driveability problemsduring a cold start, try a different br

• Normally, adding 1 gallon (3.8L) of fuel is enough to restart theengine. If the vehicle is out of fuel and on a steep grade, more than1 gallon (3.8L

turn AUTO PRESET ON, and either wait five seconds for the search toinitiate or press OK to immediately initiate the search. If you pressanother contro

2. Slowly insert the funnel into theEasy Fuel™ system.3. Fill the vehicle with fuel from the portable fuel container.4. When done, clean the funnel or

vehicle after the fuel gauge indicates empty, you might not beable to refuel the full amount of the advertised capacity of thefuel tank due to the emp

Habits• Smooth, moderate operation can yield up to 10% savings in fuel.• Steady speeds without stopping will usually give the best fueleconomy.• Idlin

• Adding certain accessories to your vehicle (for example bugdeflectors, rollbars/light bars, running boards, ski racks) may reducefuel economy.• Usin

Illumination of the service engine soon indicator, charging systemwarning light or the temperature warning light, fluid leaks, strange odors,smoke or

electrical system dry out. After three driving cycles without these or anyother temporary malfunctions present, the service engine soonindicator shoul

Allow the vehicle to sit for at least eight hours without starting theengine. Then, start the engine and complete the above driving cycle. Theengine m

3. With the parking brake engaged and your foot on the brake pedal,start the engine and move the gearshift lever through all of the gearranges. Allow

Adjusting automatic transmission fluid levelsBefore adding any fluid, make sure the correct type is used. The type offluid used is normally indicated

Checking and adding manual transmission fluid (if equipped)1. Park the vehicle on a levelsurface.2. Engage the parking brake fully –put in first gear.

/ Play/Pause: Press toplay/pause a track when playing aCD.SEEK/TRACK: PressSEEK/TRACK to access theprevious/next track.CAT (Category) / FOLD (Folder):

Changing the air filter element1. Release the clamps that secure the air filter housing cover.• 2.5L I4 engine• 3.0L V6 engine2. Pull the air filter h

VEHICLE STORAGEIf you plan on storing your vehicle for an extended period of time(30 days or more), refer to the following maintenance recommendations

Note: During extended periods of vehicle storage (30 days or more),fuel may deteriorate due to oxidation. Add Motorcraft威 Gas Stabilizer orequivalent

• Check the exhaust for any foreign material that may have collectedduring storage.• Check tire pressures and set tire inflation per the Tire Label.•

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIESItem CapacityFord part name orequivalentFord part number /Ford SpecificationBrake fluid and (clutchfl

Item CapacityFord part name orequivalentFord part number /Ford SpecificationEngine oil(2.5L engine)5.3 quarts(5.0L)•Motorcraft威 SAE 5W-20Premium Synth

Item CapacityFord part name orequivalentFord part number /Ford SpecificationAutomatic transmissionfluid9.0 quarts (8.5L)6Motorcraft威MERCON威 LV ATF7XT-

6Indicates only approximate dry-fill capacity. Some applications may vary based on cooler size andif equipped with an in-tank cooler. The amount of tr

ENGINE DATAEngine 2.5L I4 Engine 3.0L V6 EngineCubic inches 152 183Required fuel Minimum 87 octane Minimum 87 octane or E85Firing order 1-3-4-2 1-4-2-

IDENTIFYING YOUR VEHICLESafety Compliance Certification LabelThe National Highway Traffic SafetyAdministration Regulations requirethat a Safety Compli

SHUFFLE: Press SHUFFLE to switch on/off and begin/stop random play.The system will only shuffle the disc currently playing.Satellite Radio (if equippe

The Vehicle Identification Number (VIN) contains the followinginformation:1. World manufacturer identifier2. Brake system / Gross VehicleWeight Rating

FORD CUSTOM ACCESSORIES FOR YOUR VEHICLEA wide selection of Ford Custom Accessories are available for yourvehicle through your local Ford or Ford of C

Peace of mind•Keyless entry keypad •Protective seat covers*•Remote start system •Windshield wiper shaker*•Vehicle security system •Back up camera*•Whe

FORD ESP EXTENDED SERVICE PLANS (U.S. ONLY)More than 30 million Ford and Lincoln owners have discovered thepowerful protection of Ford ESP. It is the

Ford ESP Can Quickly Pay for ItselfOne service bill – the cost of parts and labor – can easily exceed theprice of your Ford ESP Service Contract. With

Ford Extended Service Plan3352011 Escape (204)Owners Guide, 2nd PrintingUSA (fus)

FORD ESP EXTENDED SERVICE PLANS (CANADA ONLY)You can get more protection for your vehicle by purchasing a FordExtended Service Plan (ESP). Ford ESP is

GENERAL MAINTENANCE INFORMATIONWhy maintain your vehicle?This guide describes the scheduled maintenance required for yourvehicle. Carefully following

different specifications and performance features. That’s why it’simportant to rely upon your dealership to properly diagnose and repairyour vehicle.F

ConvenienceMany dealerships have extended evening and Saturday hours to makeyour service visit more convenient. How’s that for quality service?Factory

MEMORY PRESETS (0–9): Thereare 30 available presets, 10 each forSAT1, SAT2 and SAT3. To savesatellite channels in your memorypresets, tune to the desi

Engine oil/coolant change intervalsEngine oil As indicated by the message center (can be upto one year or 10,000 miles [16,000 km])Engine coolant,init

Multi-point inspection - Recommended at every visitAccessory drive belt(s) Operation of horn, exterior lampsand hazard warning systemBattery performan

Scheduled Maintenance Guide3422011 Escape (204)Owners Guide, 2nd PrintingUSA (fus)

NORMAL SCHEDULED MAINTENANCE AND LOGFor your convenience, your vehicle is equipped with a message centerwhich determines the proper oil change service

Oil Change Service Interval* 1 23456789101112131415Change engine oil and filter • ••••••••••••••Rotate tires, inspect tire wear and measuretread depth

Perform the services noted in the following table at the specifiedtime/mileage (km) period either within 3,000 miles (4,800 km) of theOIL CHANGE REQUI

Every 150,000 miles(240,000 km)Change automatic transmission fluid and filter(except 5–speed TorqShift威 transmission) (filternot required on 6F35, 6F5

Maintenance schedule logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDAT

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

an audible prompt. Press OK while SONG ALERT is in the display andthe system will take you to the channel playing the desired song. Youcan save up to

SPECIAL OPERATING CONDITIONSIf you operate your vehicle primarily in one of the more demandingconditions listed below, you will need to have some item

Extensive idling and/or low-speed driving for long distances as in heavycommercial use such as delivery, taxi, patrol car or liveryAs required – Chang

Operating in dusty conditions such as unpaved or dusty roadsInspect frequently, service asrequired– Replace cabin air filter (if equipped)– Replace en

Off-road operationInspect frequently, service asrequired– Inspect steering linkage, ball joints and U-joints;lubricate if equipped with grease fitting

Special operating condition logDEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER

DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HOURS:DAT E:MILEAGE:DEALER VALIDATION:P&A CODE:RO#: HO

EXCEPTIONSIn addition, there are several exceptions to the Normal Schedule. Theyare listed below:Normal vehicle axle maintenance❑Rear axles and power

ENGINE COOLANT CHANGE RECORDInitial change 6 years or 100,000 miles (160,000 km)(whichever comes first)After initial change Every 3 years or 50,000 mi

AAccessory delay ...73Active Park Assist ...231AdvanceTrac ...214Airbag supplement

Changing a tire ...253Child safety seats ...157attaching with tether straps ..163in front seat ...

Note: you must be tuned to the specific channel you want tolock/unlock when using this feature.b. CHANGE PIN: Press OK when CHANGE PIN is displayed. T

coolant ...297fail-safe cooling ...301idle speed control ...295lubrication speci

IIgnition ...205, 328Illuminated visor mirror ...68Infant seats(see Safety seats) ...157Inspec

NNavigation system ...46OOctane rating ...307Oil (see Engine oil) ...291Overdrive ...

Scheduled Maintenance GuideNormal ScheduledMaintenance and Log ...343Seats ...111child safety seats .

VVehicle Identification Number(VIN) ...329Vehicle loading ...192Ventilating your vehicle

ALL SEATS (Occupancy mode, if equipped): Press SOUNDrepeatedly to reach the Occupancy mode setting. PressSEEK/TRACK to select and optimize sound for A

Your vehicle is equipped with anAuxiliary Input Jack (AIJ). TheAuxiliary Input Jack provides a wayto connect your portable musicplayer to the in-vehic

7. Adjust the sound on your portable music player until it reaches thelevel of the FM station or CD by switching back and forth between theAUX and FM

CONGRATULATIONSCongratulations on acquiring your new Ford. Please take the time to getwell acquainted with your vehicle by reading this handbook. The

Your vehicle may be equipped with aUSB port located on the instrumentpanel. This feature allows you toplug in media playing devices,memory sticks, and

CD/CD player careDo:• Handle discs by their edges only.(Never touch the playingsurface).• Inspect discs before playing.• Clean only with an approved C

CDs with homemade paper(adhesive) labels should not beinserted into the CD player asthe label may peel and cause theCD to become jammed. It isrecommen

Sample MP3 structureIf you are burning your own MP3discs, it is important to understandhow the system will read thestructures you create. While variou

• Terrain: Hills, mountains, tall buildings, bridges, tunnels, freewayoverpasses, parking garages, dense tree foliage and thunderstorms caninterfere w

Radio Display Condition Action RequiredACQUIRING Radio requires morethan two seconds toproduce audio forthe selectedchannel.No action required. Thisme

Radio Display Condition Action RequiredNO TEXT Categoryinformation notavailable.Category information notavailable at this time onthis channel. The sys

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1.Fan speed adjustment: Turn to select fan speed.2.RRear defroster: Press to activate/deactivat

9. Temperature control: Controls the temperature of the airflow in thevehicle.10.Passenger heated seat control (if equipped): Press toactivate/deactiv

• Do not put objects under the front seats that will interfere with theairflow to the back seats.• Remove any snow, ice or leaves from the air intake

Warning symbols on your vehicleWhen you see this symbol, it isimperative that you consult therelevant section of this guide beforetouching or attempti

DUAL AUTOMATIC TEMPERATURE CONTROL (IF EQUIPPED)1. AUTO/Driver temperature: Press to engage full automaticoperation. Select the desired temperature us

5. Power/ : Press to activate/deactivate the climate controlsystem. When the system is off, outside air is prevented from enteringthe vehicle through

14. Driver heated seat control (if equipped): Press toactivate/deactivate the driver heated seat. See Heated seats in theSeating and Safety Restraints

• Manual operation:1. Select MAX A/C.2. Selector .3. Select(recirculated air) to provide colder airflow.4. Set the temperature to 60°F (16°C).5. Set h

HEADLAMP CONTROLRotate the headlamp control to thefirst position to turn on theparking lamps.Rotate to the second positiontoturn on the headlamps.Rota

Autolamp delay system (if equipped)If your vehicle is equipped with autolamps, you can set the delay time tokeep the headlights on for up to three min

Flash-to-passPull toward you slightly to activateand release to deactivate.Daytime running lamps (DRL) (if equipped)Turns the low beam headlamps on wi

Note: If the battery is disconnected, discharged, or a new battery isinstalled, the dimmer switch requires re-calibration. Rotate the dimmerswitch fro

5. Locate the vertical adjuster onthe headlamp, then usea4mmsocket to turn the adjuster eithercounterclockwise (to adjust up) orclockwise (to adjust d

Map lamps (without moon roof)The map lamp controls (withoutmoon roof) are located on the domelamp.• Press the button on either side ofeach map lamp to

Do not add friction modifier compounds or special break-in oils since theseadditives may prevent piston ring seating. See Engine oil in theMaintenance

Ambient lighting (if equipped)Illuminates footwells, cupholders,the console bin and the console traywith a choice of several colors. Theambient lighti

Take your vehicle to a dealer for service if any of the above conditions ofunacceptable moisture are present.Using the right bulbsReplacement bulbs ar

Replacing headlamp bulbs1. Make sure the headlamp control is in the off position.2. Open the hood.3. Reach over the front bolster.4. Remove the bulb b

5. Carefully pull the bulb out of thesocket and push in the new bulb.6. Install the bulb socket into thelamp assembly and rotate clockwise.Replacing f

Replacing high-mount brake lamp bulbs1. Remove the two screws and movethe lamp assembly away from theliftgate.2. Remove the bulb holder from thelamp a

4. Pull bulb straight out of socketand push in the new bulb.5. Install the bulb socket into thelamp assembly and rotate clockwise.6. To install, caref

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

Rear window wiper/washer controlsFor rear wiper operation, rotate therear window wiper and washercontrol to the desired position.Select:2 — Normal spe

ILLUMINATED VISOR MIRROR (IF EQUIPPED)Lift the mirror cover to turn on thevisor mirror lamp.Slide-on-rod featureRotate the visor towards the sidewindo

Usually, when something affects the compass readings, the compass willcorrect itself after a few days of operating your vehicle in normalconditions. I

DATA RECORDINGService Data RecordingService data recorders in your vehicle are capable of collecting andstoring diagnostic information about your vehi

Compass calibration adjustmentPerform compass calibration in an open area free from steel structuresand high voltage lines. For optimum calibration, t

The tray and inside bin can beremoved to open up space to fit alaptop computer, MP3 players, CDsor handbags. To remove, open theconsole lid and pull t

To have full capacity usage of your power point, the engine is required tobe running to avoid unintentional discharge of the battery. To preventthe ba

Window lockThe window lock feature allows onlythe driver to operate the powerwindows.To lock out all the window controls(except for the driver’s) pres

Do not clean the housing or glass of any mirror with harshabrasives, fuel or other petroleum-based cleaning products.Note: If equipped with a rearview

Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not re

3. Press and release SET +.4. Take your foot off the accelerator pedal.5. The indicatorlight on the instrument cluster will turn on.Note:• Vehicle spe

Turning off speed controlTo turn off the speed control, press OFF or turn off the ignition.Note: When you turn off the speed control or the ignition,

SYNC威 system hands-freecontrol feature (if equipped)Press briefly to use the voicecommand feature. You will hear atone and LISTENING will appear inthe

To open the moon roof: The moonroof is equipped with an automatic,one-touch, opening, closing andventing feature. Press and releasethe rear portion of

Note: EDR data is recorded by your vehicle only if a non-trivialcrash situation occurs; no data is recorded by the EDR undernormal driving conditions

The moon roof has a sliding shade that can be opened or closed whenthe glass panel is shut. To close the shade, pull it toward the front of thevehicle

Read the instructions completely before attempting to program theCar2U威 system. Because of the steps involved, it may be helpful to haveanother person

you will know which actions are time-sensitive. If you do not follow thetime-sensitive actions, the device will time out and you will have torepeat th

4. Press and release the button again. The garage door should move,confirming that programming is successful. If your garage door does notoperate, rep

Switchposition 12345678 9101112Up, onor +LLLLLLLL L L L LMiddle,neutralor 0MMMMMMMMMMMMDown,offor–RRRRRRRR R R R RL=left; M=middle; R=right3. To input

After successful programming, you will be able to operate your Car2U威system by pressing the button you programmed to activate the opener.The indicator

POSITIVE RETENTION FLOOR MATWARNING: Do not install additional floor mats on top of thefactory installed floor mats as they may interfere with theacce

WARNING: Make sure that the liftgate door and/or window areclosed to prevent exhaust fumes from being drawn into thevehicle. Exhaust fumes contain car

The larger, rearward, compartmentis for customer storage. To open, liftthe lid with the pull latch. The lidcan be removed to allow for flexiblestorage

WARNING: When loading the roof rail crossbars, it isrecommended to evenly distribute the load, as well as maintain alow center of gravity. Loaded vehi

Ford or its vendors to receive this information, do not activatethe service. Ford Motor Company and the vendors it uses toprovide you with this inform

3. Use a long, flat object to depressthe tongue in the endcaps on bothsides of the cross-bar.4. Slide the cross-bar assembly offthe end of the rail.Be

KEYSYour vehicle is equipped with twoIntegrated Keyhead Transmitters(IKTs). The key blade functions as aprogrammed key which starts thevehicle and unl

MYKEY™The MyKey™ feature allows you to program a restricted driving mode topromote good driving habits. All but one of the keys programmed to thevehic

2. Press and release the RESET button. HOLD RESET TO CONFIRMMYKEY will be displayed.3. Press and hold the RESET button for two seconds until MARK THIS

Clear MyKey™To reset all MyKeys™ as admin keys do the following:1. Turn the vehicle on using the admin key.2. Press SETUP until PRESS RESET TO CLEAR M

Note: For all vehicles, the number of MYKEY(S) PROGRAMMED orADMIN KEYS PROGRAMMED that is displayed in the MyKey™ SystemStatus menus will include the

Condition Potential CausesCannot clear MyKey™ • Key in the ignition is a MyKey™• No MyKeys™ are programmed tothe vehicle. Refer to Create aMyKey™ sect

POWER DOOR LOCKS• Press thecontrol to unlock alldoors.• Press thecontrol to lock alldoors.Door key unlocking/lockingUnlocking the doorsTurn the key in

Note: The autolock feature can be activated/deactivated independentlyof the autounlock feature.Before following the activation or deactivation procedu

Message center procedure (if equipped)For information on activating/deactivating the autolock feature using thevehicle’s message center, refer to Mess