Ford 2004 Crown Victoria v.1 Manual de usuario

Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 15Entertainment Systems 20AM/FM stereo cassette with CD 20AM/FM stereo with CD

WARNING LIGHTS AND CHIMESStandard instrument clusterOptional instrument clusterWarning lights and gauges can alert you to a vehicle condition that may

How to disengage the automatic locking modeFord Motor Company recommends that all passenger safety beltassemblies and attaching hardware should be ins

Lap beltsAdjusting the front center seat lap beltThe lap belt should fit snugly and as low as possible around thehips, not across the waist.The lap be

Safety belt warning light and indicator chimeThe safety belt warning light illuminates in the instrument cluster and achime sounds to remind the occup

If... Then...The driver’s and frontpassenger’s safety belts arebuckled before the ignitionswitch is turned to the ONposition or less than 1-2minutes h

The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data)Reasons given... Consider...“Crashes are ra

Reasons given... Consider...“I have an air bag” Air bags offer greater protection whenused with safety belts. Frontal airbagsare not designed to infla

To reduce the risk of injury, do not deactivate/activate the BeltMinder feature while driving the vehicle.1. Turn the ignition switch to the RUN (or O

Safety belt maintenanceInspect the safety belt systems periodically to make sure they workproperly and are not damaged. Inspect the safety belts to ma

Important SRS precautionsThe SRS is designed to work withthe safety belt to help protect thedriver and right front passengerfrom certain upper body in

Do not attempt to service, repair, or modify the air bagsupplemental restraint systems or its fuses. See your Ford orLincoln Mercury dealer.The front

misfire is occurring which could damage your catalytic converter. Drivein a moderate fashion (avoid heavy acceleration and deceleration) andhave your

How does the air bag supplemental restraint system work?The air bag SRS is designed toactivate when the vehicle sustainslongitudinal deceleration suff

The SRS consists of the following items:• Driver and passenger air bag modules (which include the inflators andair bags)• Driver and passenger side ai

• A series of five beeps will be heard. The tone pattern will repeatperiodically until the problem and/or light are repaired.If any of these things ha

How does the side air bag system work?The design and development of theside airbag system includedrecommended testing proceduresthat were developed by

Several air bag systemcomponents get hot afterinflation. Do not touch them afterinflation.If the side air bag has deployed, the air bag will not funct

SAFETY RESTRAINTS FOR CHILDRENSee the following sections for directions on how to properly use safetyrestraints for children. Also see Air bag supplem

Child booster seatsChildren outgrow a typical convertible or toddler seat when they weigh40 pounds and are around 4 years of age. Although the lap/sho

Types of booster seatsThere are two types of belt-positioning booster seats:• Those that are backless.If your backless booster seat has aremovable shi

Follow all instructions provided by the manufacturer of thebooster seat.Never put the shoulder belt under a child’s arm or behind theback because it e

When installing a child safety seat:• Review and follow the informationpresented in the Air bagsupplemental restraint system(SRS) section in this chap

Anti-lock brake system: If theABS light stays illuminated orcontinues to flash, a malfunction hasbeen detected, have the systemserviced immediately. N

Rear-facing child seats or infant carriers should never be placedin the front seats.Installing child safety seats with combination lap and shoulderbel

3. While holding the shoulder andlap belt portions together, route thetongue through the child seataccording to the child seatmanufacturer’s instructi

7. Pull the lap belt portion acrossthe child seat toward the buckle andpull up on the shoulder belt whilepushing down with your knee on thechild seat.

The tether strap anchors in yourvehicle are in the following positions(shown from top view):Attach the tether strap only to the appropriate tether anc

5. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safetyseat may not be retained properlyin the even

Never attach two LATCH child safety seats to the same anchor.In a crash, one anchor may not be strong enough to hold twochild safety seat attachments

Follow the child seat manufacturer’sinstructions to properly install achild seat with LATCH attachments.Two plastic LATCH guides can beobtained at no

STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo

Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,

4. Make sure the parking brake isset.5. Turn the key to 4 (ON) withoutturning the key to 5 (START).HOOD123452004 Crown Victoria (cro)Owners Guide (pos

Air suspension (if equipped):• Standard instrument cluster• Optional instrument clusterIlluminates when the air suspensionis turned OFF, the load limi

Make sure the corresponding lights illuminate or illuminate briefly. If alight fails to illuminate, have the vehicle serviced.• If the driver’s safety

To reduce the risk of electrical shock, do not use your heaterwith ungrounded electrical systems or two-pronged (cheater)adapters.Guarding against exh

emphasis on improved performance and environmental considerationscan lead to more dust than in the past. Brake dust can be cleaned byweekly washing wi

With the ABS light on, the anti-lockbrake system is disabled and normalbraking is still effective unless thebrake warning light also remainsilluminate

Pull the release lever to release thebrake. Driving with the parkingbrake on will cause the brakes towear out quickly and reduce fueleconomy.TRACTION

During Traction Control娂 operation you may hear an electric motor typeof sound coming from the engine compartment and the engine will not“rev-up” when

If the power steering system breaks down (or if the engine is turnedoff), you can steer the vehicle manually, but it takes more effort.If the steering

The air suspension shut-off switch islocated on the left side of the trunk.If this switch is in the OFF position,the rear air suspension will notopera

Do not drive your vehicle until you verify that the brakelampsare working.Always set the parking brake fully and make sure the gearshift islatched in

R (Reverse)With the gearshift lever in R (Reverse), the vehicle will move backward.Always come to a complete stop before shifting into and out of R(Re

MESSAGE CENTER INDICATOR LIGHTS (IF EQUIPPED)Speed control: This light comes onwhen either the SET/ACCEL orRESUME controls are pressed. Itturns off wh

The transmission control indicator light (TCIL) will illuminate on theinstrument cluster.• Standard instrument cluster• Optional instrument clusterDri

Forced downshifts• Allowed in(Overdrive) or Drive.• Depress the accelerator to the floor.• Allows transmission to select an appropriate gear.If your v

VEHICLE LOADING – WITH AND WITHOUT A TRAILERThis section will guide you in the proper loading of your vehicle and/ortrailer, to keep your loaded vehic

GVW (Gross Vehicle Weight) – is the Vehicle Curb Weight + cargo +passengers.GVWR (Gross Vehicle WeightRating) – is the maximumallowable weight of the

GCWR (Gross Combined Weight Rating) – is the maximum allowableweight of the vehicle and the loaded trailer – including all cargo andpassengers – that

Your loaded trailer should weigh no more than 907 kg (2,000 lbs.). Donot exceed the GVWR specified on the certification label.Towing trailers beyond t

Driving while you towWhen towing a trailer:• Turn off the speed control. The speed control may shut offautomatically when you are towing on long, stee

Launching or retrieving a boatDisconnect the wiring to the trailer before backing the trailerinto the water. Reconnect the wiring to the trailer after

GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program

Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will

GAUGESStandard instrument cluster gaugesOptional instrument cluster gaugesSpeedometer: Indicates the current vehicle speed.• Standard instrument clust

The fuel pump shut-off switch islocated on the left side of the trunkbehind the left rear tail light and thetrunk liner.Use the following procedure to

Note: Always replace a fuse with one that has the specified amperagerating. Using a fuse with a higher amperage rating can cause severe wiredamage and

The fuses are coded as follows.Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description1 15A Audio, CD changer2 5A Audio (optional)

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description8 25A Powertrain Control Module (PCM)power relay, Coil-on plugs, Radionoise

Fuse/RelayLocationFuse AmpRatingPassenger Compartment FusePanel Description21 15A LCM for park lamps and interiorillumination, Autolamp/Sunloadsensor2

Always replace the cover to the power distribution box beforereconnecting the battery or refilling fluid reservoirsIf the battery has been disconnecte

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription9 — Not used10 — Not used11 20A* Daytime Running Lamps (DRL)12 — Not used13 — Not use

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription108 50A** Police rear access power point(Police vehicles only)109 50A** Light bar (Po

Fuse/RelayLocationFuse AmpRatingPower Distribution BoxDescription401 — Not used501 Diode PCM502 Diode A/C clutch503 — Not used601 — Not used602 20A**

• tow a trailer.• use tire chains.• drive through an automatic car wash, because of the vehicle’s reducedground clearance.• try to repair the temporar

• Optional instrument clusterEngine coolant temperature gauge:• Standard instrument cluster• Optional instrument clusterIndicates engine coolanttemper

2. Place gearshift lever in P (Park),turn engine OFF and block thediagonally opposite wheel.3. Remove the spare tire and thejack. The jack could be lo

5. Locate pry off notch (ifequipped) and remove the centerornament from the aluminum wheelwith the tapered end of the wheelnut wrench that came with y

• Position the jack according to thefollowing guides and turn the jackhandle clockwise until the wheelis completely off the ground.To lessen risk of p

Wheel lug nut torque specificationsRetighten the lug nuts to the specified torque at 800 km (500 miles)after any wheel disturbance (tire rotation, cha

2. Do not disconnect the battery of the disabled vehicle as this coulddamage the vehicle’s electrical system.3. Park the booster vehicle close to the

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat

4. Make the final connection of the negative (-) cable to an exposedmetal part of the stalled vehicle’s engine, away from the battery and thecarbureto

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member of a roadside assistance program, y

Odometer: Registers the total kilometers (miles) of the vehicle.• Standard instrument cluster• Optional instrument clusterRefer to Electronic Message

GETTING THE SERVICES YOU NEEDAt homeYou must take your Ford vehicle to an authorized Ford dealer forwarranty repairs. While any Ford dealership handli

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo

In the United States, a warranty dispute must be submitted to theDispute Settlement Board before taking action under the Magnuson-MossWarranty Act, or

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY)The Dispute Settlement Board is:• an independent, third-party arbitration program for warranty disputes.• avai

Board membershipThe Board consists of:• Three consumer representatives• A Ford or Lincoln Mercury dealership representativeConsumer candidates for Boa

Oral presentationsIf you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral

UTILIZING THE MEDIATION/ARBITRATION PROGRAM(CANADA ONLY)In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a

If your vehicle must be serviced while you are traveling or living inCentral or South America, the Caribbean, or the Middle East, contact thenearest F

IN CALIFORNIA (U.S. ONLY)California Civil Code Section 1793.2(d) requires that, if a manufactureror its representative is unable to repair a motor veh

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

• Optional instrument clusterRefer to Electronic Message Centerin the Driver Controls chapter forTrip A and Trip B features.Battery voltage gauge (ife

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is

PAINT CHIPSYour dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam

• Cover the highlighted areas to prevent water damage when cleaningthe engine.• Never wash or rinse the engine while it is running; water in therunnin

• Do not use fuel, kerosene, or paint thinner to clean any parts.• Wiper blades can be cleaned with isopropyl (rubbing) alcohol orwindshield washer so

Do not use cleaning solvents, bleach or dye on the vehicle’ssafety belts, as these actions may weaken the belt webbing.Do not use chemical solvents or

Motorcraft Vinyl Cleaner (Canada only) (CXC-93)Motorcraft Vinyl Conditioner (Canada only) (CXC-94)Motorcraft Deluxe Leather and Vinyl Cleaner (not ava

SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a

OPENING THE HOOD1. Inside the vehicle, pull the hoodrelease handle located under theinstrument panel.2. Go to the front of the vehicle andrelease the

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

5. Locate and carefully remove theengine oil level indicator (dipstick).6. Wipe the indicator clean. Insert the indicator fully, then remove itagain.•

Fuel gauge: Indicates approximately how much fuel is left in the fueltank (when the ignition is in the ON position). The fuel gauge may varyslightly w

• If required, add engine oil to theengine. Refer to Adding engineoil in this chapter.• Do not overfill the enginewith oil. Oil levels above thismark

Engine oil and filter recommendationsLook for this certificationtrademark.Use SAE 5W-20 engine oil.Only use oils “Certified For Gasoline Engines” by t

BATTERYYour vehicle is equipped with aMotorcraft maintenance-free batterywhich normally does not requireadditional water during its life ofservice.How

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a

If the battery has been disconnected or a new battery has been installed,the clock and radio settings must be reset once the battery isreconnected.• A

When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “cold fill level” or within the “c

Do not add engine coolant when the engine is hot. Steam andscalding liquids released from a hot cooling system can burn youbadly. Also, you can be bur

To reduce the risk of personal injury, make sure the engine iscool before unscrewing the coolant pressure relief cap. Thecooling system is under press

Coolant refill capacityTo find out how much fluid your vehicle’s cooling system can hold, referto Refill capacities in this chapter.Fill your engine c

How fail-safe cooling works• Standard cluster• Optional clusterIf the engine begins to overheat:• The engine coolant temperature gauge will move to th

Locks and Security 74Keys 74Locks 74Anti-theft system 76Seating and Safety Restraints 88Seating 88Safety restraints 92Air bags 107Child restraints 115

PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD (IF EQUIPPED)1. Eject: Press to eject a tape.2. Eject: Press to eject a CD.3. Bass: Allows you to increase ord

• The engine will completely shut down, causing steering and brakingeffort to increase.Once the engine temperature cools, the engine can be re-started

If you do not use the proper fuel filler cap, excessive pressure orvacuum in the fuel tank may damage the fuel system or causethe fuel cap to disengag

splashed on the skin, promptly wash skin thoroughly with soap andwater. Consult a physician immediately if you experience an adversereaction.When refu

Cap light on, can activate the Service Engine Soon warning. When thefuel filler cap is properly re-installed, the light(s) will turn off after aperiod

Fuel qualityIf you are experiencing starting, rough idle or hesitation driveabilityproblems during a cold start, try a different brand of unleaded gas

ESSENTIALS OF GOOD FUEL ECONOMYMeasuring techniquesYour best source of information about actual fuel economy is you, thedriver. You must gather inform

Calculating fuel economy1. Fill the fuel tank completely and record the initial odometer reading(in kilometers or miles).2. Each time you fill the tan

• You may want to turn off the speed control in hilly terrain ifunnecessary shifting between third and fourth gear occurs.Unnecessary shifting of this

It is important to note the box in the lower left corner of the windowsticker. These numbers represent the Range of L/100 km (MPG)expected on the vehi

permitted to intentionally remove an emission control device or preventit from working. Information about your vehicle’s emission system is onthe Vehi

Fade: Allows you to shift speakersound between the front and rearspeakers. Press FADE then pressSEL to shift the sound to the rearor the front .5. COM

condition. To ready the on-board diagnostics system for I/M testing, aminimum of 30 minutes of city and highway driving is necessary asdescribed below

BRAKE FLUID RESERVOIRThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels below the “M

Low fluid levelDo not drive the vehicle if the fluidlevel is at the bottom of the dipstickand the ambient temperature isabove 10°C (50°F).Correct flui

High fluid levelFluid levels above the safe rangemay result in transmission failure.An overfill condition of transmissionfluid may cause shift and/ore

Changing the air filter element1. Release the clamps that secure the air filter housing cover.2. Carefully separate the two halves of the air filter h

U.S. Department of Transportation-Tire quality grades: The U.S.Department of Transportation requires Ford to give you the followinginformation about t

TIRESTires are designed to give many thousands of miles of service, but theymust be maintained in order to get the maximum benefit from them.Glossary

Information on “P” type tiresP215/65R15 95H is an example of atire size, load index and speedrating. The definitions of theseitems are listed below. (

Letter rating Speed rating - km/h (mph)Q 159 km/h (99 mph)R 171 km/h (106 mph)S 180 km/h (112 mph)T 190 km/h (118 mph)U 200 km/h (124 mph)H 210 km/h (

specified government test course. For example, a tire graded 150would wear one and one-half (11⁄2) times as well on the governmentcourse as a tire gra

9. RDS: (Radio Data System):Allows you to access FM stationswhich are RDS- equipped. PressRDS then SEL to select from:Traffic — Allows you to receive

Additional information contained on the tire sidewall for “LT” typetires“LT” type tires have some additionalinformation than those of “P” typetires; t

Information on “T” type tiresT145/80D16 is an example of a tiresize.Note: The temporary tire size foryour vehicle may be different thanthis example.1.

TIRE CAREImproper or inadequate vehicle maintenance can also cause tires to wearabnormally. Here are some of the important maintenance itemsTire infla

2. Remove the cap from the valve on one tire, then firmly press the tiregauge onto the valve.3. Add air to reach the recommended air pressureNote: If

Tire rotationRotating your tires at the recommended interval (as indicated in theService Maintenance Guide that comes with your vehicle) will help you

• Rear Wheel Drive (RWD)vehicles/Four Wheel Drive (4WD)vehicles (front tires at top ofdiagram)Sometimes irregular tire wear can be corrected by rotati

the tread is worn down to 4mm (1/16th of an inch). When you see these“wear bars”, the tire is worn out and should be replaced.Inspect your tires frequ

Highway hazardsNo matter how carefully you drive there’s always the possibility that youmay eventually have a flat tire on the highway. Drive slowly t

MOTORCRAFT PART NUMBERSComponent 4.6L SOHC V8 engineAir filter element FA-1668Fuel filter FG-986BBattery-standard BXT-65–650Battery-heavy duty BXT-65–

Fluid Ford Part Name CapacityRear axle lubricant5Motorcraft SAE80W-90 Premium RearAxle Lubricant2.4L (5.0 pints)Windshield washerfluidMotorcraft Premi

15. Mute mode: Press to mute theplaying media.16. Power/volume: Press to turnthe system on/off. Turn toraise/lower the volume.17. Tape: Press to play

LUBRICANT SPECIFICATIONSItem Ford partnameFord partnumberFordspecificationBrake fluid Motorcraft HighPerformanceDOT 3 MotorVehicle BrakeFluid1PM-1 ESA

Item Ford partnameFord partnumberFordspecificationRear AxleLubricant2Motorcraft SAE80W-90Premium RearAxle LubricantXY-80W90-QL WSP-M2C197-AWindshieldw

VEHICLE DIMENSIONS (AT CURB MASS)Vehicle dimensions mm (in)(1) Overall length 5386 (212)/5538 (218)a(2) Overall width 1987 (78.2)(3) Overall height 14

IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt

Vehicle identification number (VIN)The vehicle identification number isattached to a metal tag and islocated on the driver sideinstrument panel. (Plea

Transmission/Transaxle code designationsYou can find a transmission/transaxle code on the vehicle certificationlabel which is located on the door pill

Code Transmission DescriptionElectricH One speed electricD Automatic 5–speed overdrive (5R44E)R Automatic 5–speed overdrive (5R55W)Passenger car appli

FORD ACCESSORIES FOR YOUR VEHICLEA wide selection of genuine Ford accessories are available for yourvehicle through your local authorized Ford or Ford

Floor matsInterior trim kitsLeather wrapped steering wheelsScuff platesSpeed controlLifestyleBike racksCargo organization and managementEngine block h

AABS (see Brakes) ...132Air bag supplemental restraintsystem ...107–108, 112and child safety seats ...

2. Fade: Press / to shiftsound to the front/rear speakers.3. SCN (Scan): Press to hear abrief sampling of all listenablestations or CD tracks. Press a

wheels ...181wiper blades ...182Climate control (see Airconditioning or Heating) ...

recommendations ...191refill capacities ...228specifications ...230–231Exhaust fumes ...

JJack ...158positioning ...158storage ...158Jum

fluid, checking and adding ...210fluid, refill capacity ...228fluid, specifications ...230Power Windows ...

Traction control ...134Traction-lok rear axle ...141Transmission ...137brake-shift interloc

245

246

247

248

11. Tune / Discs: In radio mode,press to move up or down thefrequency band in individualincrements.12. Seek: Press and releaseSEEK/ for previous/nexts

AM/FM STEREO (IF EQUIPPED)1. Seek: Press/ to find thenext strong station down/up thefrequency band.2. Tune: Press/ to manuallychange radio frequency d

5. Power/volume: Press to turnON/OFF; turn to increase ordecrease volume levels.6. Tone: Press TONE until thedesired level — Bass, Treble, Fadeappears

AM/FM STEREO CASSETTE (IF EQUIPPED)1. Balance: Press to shift sound tothe left/right speakers.2. Fade: Press to shift sound to therear/front speakers.

next selection). Then, press REW (for the beginning of the currentselection) or FF (to advance to the next selection). The tape MUST havea blank secti

Cleaning 180Maintenance and Specifications 186Engine compartment 187Engine oil 188Battery 192Fuel information 200Air filter(s) 214Part numbers 228Refi

13. AM/FM: Press to choose afrequency band in radio mode.14. Bass: Press/ todecrease/increase the bass output.15. Treble: Press/ todecrease/increase t

3. Turn the magazine (A) over.4. Using the disc holder releaseknob (C), pull the disc holder (B)out of the magazine.Do not pull too hard on the disc h

RADIO RECEPTION FACTORSThere are three factors that can affect radio reception:• Distance/strength: The further you travel from an FM station, theweak

CD units are designed to play commercially pressed 12 cm(4.75 in) audio compact discs only. Due to technicalincompatibility, certain recordable and re

MANUAL HEATING AND AIR CONDITIONING SYSTEM(IF EQUIPPED)1. Fan speed adjustment: Controlsthe volume of air circulated in thevehicle.2. Temperature sele

To aid in side window defogging/demisting in cold weather:1. Select NORM A/C.2. Modulate the temperature control to maintain comfort.3. Set the fan sp

3. Fan speed: Turn to manuallyincrease or decrease fan speed.4. Defrost:Distributes outside air through the windshield defrostervents and the side win

• Remove any snow, ice or leaves from the air intake area at the base ofthe windshield.To aid in side window defogging/demisting in cold weather:1. Se

HEADLAMP CONTROLTurns the lamps off.Turns on the parkinglamps, instrument panel lamps,license plate lamps and tail lamps.Turns the headlamps on.Autola

Always remember to turn on your headlamps at dusk or duringinclement weather. The Daytime Running Light (DRL) Systemdoes not activate your tail lamps

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth

Domelamp ControlThe panel dimmer control also controls the domelamp operation.• Rotate the thumbwheel fully to the right, past detent to activate thed

To see a clearer light pattern foradjusting, you may want to blockthe light from one headlamp whileadjusting the other.5. Locate the vertical adjuster

MAP/COURTESY LAMPSWithout a moon roofWith a moon roofTo turn on the map lamps, press themap lamp control.BULBSReplacing exterior bulbsCheck the operat

Function Trade NumberTail, stop, turn (rear) 3157KSide marker (rear) 194Backup lamp 3156KLicense plate lamp 168High-mount brakelamp 912Luggage compart

5. Without turning, remove the oldbulb from the lamp assembly bygently pulling it straight back out ofthe lamp assembly.To install the new bulb:Handle

4. Disconnect the electricalconnector from the bulb by pullingrearward.5. Rotate the bulb socketcounterclockwise and remove fromlamp assembly.6. Caref

5. Pull the bulb from the socket andpush in the new bulb.6. Install the bulb socket into thelamp assembly by rotating itclockwise.7. Install the lamp

Replacing high-mount brakelamp bulbs1. Make sure headlamp switch is inOFF position, then remove twoscrews from the lamp assembly.2. Carefully lift the

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

To replace the wiper blades:1. Pull the wiper arm away from thewindshield and lock into the serviceposition.2. Press and hold the tab on theblade and

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury and prevent possibledamage to others, you

or metallic objects placed in or on the vehicle may also affect compassaccuracy. Adjustments may need to be made to the zone and calibrationof the com

OVERHEAD CONSOLE WITH MOON ROOF (IF EQUIPPED)The appearance of your vehicle’s overhead console will vary according toyour option package. Some of the

2. Hold down the MODE button for5 seconds to enter zone mode. Thedisplay will read PRESS RESET TOSET ZONE XX where XX is thecurrent zone.3. Release th

4. Press the RESET button tode-calibrate the compass. Thedisplay will read CIRCLE SLOWLYTO CALIBRATE for a few secondsand then display a direction wit

3. After 20 seconds, the display willread CHANNEL X TRANING toindicate training has started.Continue to hold the button.Note: If the channel being tra

brand. If there is difficulty locating the “learn” or “smart” button refer tothe device’s owner manual or contact HomeLink威 at 1–800–355–3515 oron the

Erase modeTo erase all three HomeLink威 channel codes:1. Simultaneously press and holdbuttons 1 and 3 for 20 seconds.2. CLEARING CHANNELS will bedispla

2. After 20 seconds CHANNELSCLEARED is displayed. Continue tohold the buttons.3. After 10 more seconds,CHANNELS DEFAULTED isdisplayed when all the cha

POWER WINDOWS (IF EQUIPPED)When closing the powerwindows, you should verifythey are free of obstructions andensure that children and/or petsare not in

POWER SIDE VIEW MIRRORSTo adjust your mirrors:1. Selectto adjust the leftmirror orto adjust the rightmirror.2. Move the control in the directionyou wi

SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and

Do not block the sensor on thebackside of the mirror since thismay impair proper mirrorperformance.Press the control to turn the mirrorOFF or AUTO.The

Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas

Resuming a set speedPress the RES/RESUME control andrelease it. This will automaticallyreturn the vehicle to the previouslyset speed. The RES/RESUMEco

• Depress the brake pedal until thedesired vehicle speed is reached,press the SET ACCEL control.Turning off speed controlThere are two ways to turn of

STEERING WHEEL CONTROLS (IF EQUIPPED)Radio control features• Press MODE to select AM, FM1,FM2, TAPE or CD (if equipped).In Radio mode:• Press NEXT to

To close the moon roof:• Press and hold the front portion of the control.• To close from the vent position, press and hold the rear portion of thecont

ProgrammingDo not program HomeLink威 with the vehicle parked in the garage.Note: Some vehicles may require the ignition switch to be turned to thesecon

Note: If the red light blinks rapidly for two seconds and then turns to acontinuous red, proceed with steps 6 through 8 to completeprogramming of a ro

Operating the HomeLink姞 Wireless Control SystemTo operate, simply press and releasethe appropriate HomeLink威 button.Activation will now occur for thet

ELECTRONIC MESSAGE CENTER (IF EQUIPPED)The electronic message center onlyworks when the ignition is in theON position.The message center allows you to

Front seat mounted rear facing child or infant seats shouldNEVER be used in front of a passenger side air bag unless theair bag can be and is turned O

SelectEach press of the SELECT controlwill select a different function.• Press the right side of the controlto advance the function to theright.• Pres

The message center will remain inthe DTE function until the SELECTcontrol is pressed to changefunctions.DTE is calculated using a runningaverage fuel

TRIP A and TRIP BThese two functions allow you tosee how far you have traveled sinceyou last reset. Trip A and Trip B arecompletely independent and mu

such equipment. Mobile Communications can enhance personal safetyand security when appropriately used, particularly in emergencysituations. Safety mus

KEYSThe vehicle is equipped with a master (black) key and valet (gray) keylock system. The master key will access doors, trunk, glove box, ignitionand

Childproof door locksWhen these locks are set, the reardoors cannot be opened from theinside. The rear doors can beopened from the outside when thedoo

Keep vehicle doors andluggage compartmentlocked and keep keys and remotetransmitters out of a child’s reach.Unsupervised children could lockthemselves

Unlocking the doorsPress this control to unlock thedriver’s door. The interior lamps willilluminate.Press the control a second timewithin five seconds

7. After a five to ten second delay, the door locks will cycle lock/unlockto confirm successful programming.8. After having waited the necessary time

To replace the battery:1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE RUBBER COVERAND CIR

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-

Replacing lost transmittersTake all your vehicle’s transmittersto your dealer if service is required.If a remote transmitter has been lostand you woul

The inside lights will not turn off if:• they have been turned on with the dimmer control, or• any door is open.The battery saver will shut off the in

7. With the ignition still in the ON position, press the unlock controlonce. After a five to ten second delay, the door will lock/unlock toconfirm suc

4. Press 1 • 2 to store the first personal code.5. The doors will lock then unlock to confirm programming of the newcode.To store a second personal co

Unlocking the doors and releasing the trunk with the keyless entrysystemTo unlock the driver door, enter either the factory-set code or personalcode (

Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the 3(OFF) or 2 (LOCK) position. Theindicator on the instrument panelw

If your keys are lost or stolen you will need to do the following:• Use your spare key to start the vehicle, or• Have your vehicle towed to a dealersh

5. Within twenty seconds of removing the second coded key, insert thenew unprogrammed key (new key) into the ignition and turn the ignitionfrom 3 (OFF

SEATINGAdjustable head restraintsYour vehicle’s seats are equipped with head restraints which arevertically adjustable. The purpose of these head rest

Lift handle to move seat forward orbackward.Pull lever up to adjust seatback.Using the manual recline function (if equipped)Never adjust the driver’s

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng

To adjust the front seatback usingthe manual recliner:• Lift and hold the handle locatedon the side of the seat.• Lean against the seatback toadjust i

The heated seat module resets at every ignition run cycle. While theignition is in the run position, activating the high or low heated seatswitch enab

Press to move the seat forward orbackward.Press to move the front portion ofthe seat cushion up or down.Press to move the rear portion ofthe seat cush

Your vehicle’s Personal Safety System consists of the following items:• Driver and passenger dual-stage air bag supplemental restraints• Driver and fr

information early in the crash event on the severity of the impact. Thisallows your Personal Safety System to distinguish between differentlevels of c

Front safety belt usage sensorsThe front safety belt usage sensors detect whether or not the driver andfront outboard passenger safety belts are faste

If any of these things happen, even intermittently, have the PersonalSafety System serviced at your dealership or by a qualified technicianimmediately

Always transport children 12 years old and under in the backseat and always properly use appropriate child restraints.Safety belts and seats can becom

The front outboard and rear safety restraints in the vehicle arecombination lap and shoulder belts. The front outboard passenger andrear seat safety b

How to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward until the entirebelt