Ford 2003 Taurus v.1 Manual de usuario

Introduction 4Instrument Cluster 10Warning and control lights 10Gauges 13Entertainment Systems 15AM/FM stereo cassette with CD 15AM/FM stereo with CD

WARNING LIGHTS AND CHIMESWarning lights and gauges can alert you to a vehicle condition that maybecome serious enough to cause expensive repairs. A wa

Several air bag systemcomponents get hot afterinflation. Do not touch them afterinflation.If the side air bag has deployed, the air bag will not funct

Never let a passenger hold a child on his or her lap while thevehicle is moving. The passenger cannot protect the child frominjury in a collision.Alwa

Booster seats should be used until you can answer YES to ALL of thesequestions:• Can the child sit all the way backagainst the vehicle seat back withk

The shoulder belt should cross the chest, resting snugly on the center ofthe shoulder. The lap belt should rest low and snug across the hips,never up

safety seat you put in your vehicle. If you do not install and use thesafety seat properly, the child may be injured in a sudden stop orcollision.When

Children 12 and under should be properly restrained in the rearseat whenever possible.1. Position the child safety seat in aseat with a combination la

4. Insert the belt tongue into theproper buckle (the buckle closest tothe direction the tongue is comingfrom) for that seating position untilyou hear

8. Allow the safety belt to retract toremove any slack in the belt.9. Before placing the child in theseat, forcibly move the seat forwardand back to m

Attaching child safety seats with tether strapsMost new forward-facing child safety seats include a tether strap whichgoes over the back of the seat a

4. Open the tether anchor cover.5. Clip the tether strap to theanchor as shown.If the tether strap is clippedincorrectly, the child safetyseat may not

Driving a vehicle with the brake system warning light on isdangerous. A significant decrease in braking performance mayoccur. It will take you longer

Your vehicle has LATCH anchors for child seat installation at the seatingpositions marked with the child seat symbol.All the LATCH lower anchors areeq

Attach LATCH lower attachments of the child seat only to theanchors shown.If you install a child seat with rigid LATCH attachments, do not tightenthe

STARTINGPositions of the ignition1. ACCESSORY, allows the electricalaccessories such as the radio tooperate while the engine is notrunning.2. LOCK, lo

Do not park, idle, or drive your vehicle in dry grass or other dryground cover. The emission system heats up the enginecompartment and exhaust system,

• Make sure the gearshift is in P(Park).• Turn the key to 4 (ON) withoutturning the key to 5 (START).Make sure the corresponding lights illuminate or

3. If the temperature is below -12° C (10° F) and the engine does notstart in 15 seconds on the first try, turn the key OFF and wait 10seconds and try

Using the engine block heater (if equipped)An engine block heater warms the engine coolant which aids in startingand heater/defroster performance. Use

Using ABSWhen hard braking is required, apply continuous force on the brakepedal; do not pump the brake pedal since this will reduce theeffectiveness

TRACTION CONTROL姟 (IF EQUIPPED)Your vehicle may be equipped with a Traction Control娂 system. Thissystem helps you maintain the stability and steerabil

If the steering wanders or pulls, check for:• an underinflated tire• uneven tire wear• loose or worn suspension components• loose or worn steering com

Traction Control娂 active (ifequipped): Illuminates when theTraction Control娂 is active, refer tothe Driving chapter for moreinformation.Low fuel: Illu

If the parking brake is fully released, but the brake warning lampremains illuminated, the brakes may not be working properly.See your dealer or a qua

Understanding the gearshift positions of the 4–speed automatictransaxleYour transaxle is equipped with an adaptive learning strategy found inthe vehic

Always set the parking brake fully and make sure the gearshift islatched in P (Park). Turn the ignition to the LOCK position andremove the key wheneve

If necessary, try turning the Traction Control娂 system off. This will allowthe wheels to spin, which may help to free your stuck vehicle. For moreinfo

• GCW (Gross Combined Weight): The combined weight of thetowing vehicle (including occupants and cargo) and the loaded trailer.• GCWR (Gross Combined

TRAILER TOWINGYour vehicle is classified as a light duty towing vehicle. The amount ofweight you can safely tow depends on the type of engine you have

3.0L 4-Valve Duratec EngineModel PassengerLoad - #/kg(lbs.)Luggage Load -kg (lbs.)Max TrailerWt.- kg (lbs.)Sedan 5/340 (750) 0 590 (1300)2/135 (300) 7

Trailer brakesElectric brakes and manual, automatic or surge-type trailer brakes aresafe if installed properly and adjusted to the manufacturer’sspeci

• The trailer tongue weight should be 10–15% of the loaded trailerweight.• After you have traveled 80 km (50 miles), thoroughly check yourhitch, elect

GETTING ROADSIDE ASSISTANCETo fully assist you should you have a vehicle concern, Ford MotorCompany offers a complimentary roadside assistance program

Headlamps on warning chime: Sounds when the headlamps or parkinglamps are on, the ignition is off (and the key is not in the ignition) andthe driver’s

Canadian customers who require roadside assistance, call1–800–665–2006.If you need to arrange roadside assistance for yourself, Ford MotorCompany will

If your vehicle is a sedan, the fuelpump shut-off switch is located onthe right side of the trunk behindthe trunk liner.If your vehicle is a wagon, th

FUSESIf electrical components in thevehicle are not working, a fuse mayhave blown. Blown fuses areidentified by a broken wire withinthe fuse. Check th

Passenger compartment fuse panelThe fuse panel is located below and to the left of the steering wheel bythe brake pedal. Remove the panel cover to acc

Fuse/relaylocationFuse ampratingPassenger compartment fusepanel description11 15A Integrated control panel (ICP),Rear washer wiper control, Frontwashe

Fuse/relaylocationFuse ampratingPassenger compartment fusepanel description30 15A Horns and horn switch, OBD IIconnector31 — Not used32 10A ABS, DRL r

Power distribution boxThe power distribution box islocated in the engine compartment.The power distribution box containshigh-current fuses that protec

The high-current fuses are coded as follows.Fuse/relaylocationFuse ampratingPower distribution boxdescription1 60A** Fuse junction panel2 30A** Powert

Fuse/relaylocationFuse ampratingPower distribution boxdescription20 — Not used21 15 A* Left headlamp22 10A* A/C clutch relay, PCM keep alivepower23 —

If you use the temporary spare tire continuously or do not followthese precautions, the tire could fail, causing you to lose controlof the vehicle, po

Odometer: Registers the totalkilometers (miles) of the vehicle.Trip odometer: Registers thekilometers (miles) of individualjourneys. To reset, depress

If the vehicle slips off the jack, you or someone else could beseriously injured.2. Place gearshift lever in P (Park),turn engine OFF, block thediagon

3. If equipped with a wheel coverthat’s bolted on, loosen the fiveplastic nuts with the lug nutwrench.4. Remove the center ornament or wheel cover fro

10. Remove the jack and fullytighten the lug nuts in the ordershown.11. Return the flat tire, jack and lugwrench to their proper storagelocations. Mak

Preparing your vehicleWhen the battery is disconnected or a new battery is installed, thetransmission must relearn its shift strategy. As a result, th

2. Connect the other end of the positive (+) cable to the positive (+)terminal of the assisting battery.3. Connect the negative (-) cable to the negat

4. Make the final connection of the negative (-) cable. Make theconnection to an exposed metal part of the stalled vehicle’s engine, awayfrom the batt

Removing the jumper cablesRemove the jumper cables in the reverse order that they wereconnected.1. Remove the jumper cable from the ground metal surfa

3. Remove the jumper cable from the positive (+) terminal of the boostervehicle’s battery.4. Remove the jumper cable from the positive (+) terminal of

WRECKER TOWINGIf you need to have your vehicle towed, contact a professional towingservice or, if you are a member, your roadside assistance center.It

GETTING THE SERVICES YOU NEEDAt homeFord Motor Company and Ford of Canada have authorized dealerships toservice your vehicle. It is preferred that you

AM/FM STEREO1. Clock: To set the hour, press andhold the H control. When thedesired hour appears, release thecontrol.To set the minute, press and hold

In Canada:Customer Relationship CentreFord Motor Company of Canada, LimitedP.O. Box 2000Oakville, Ontario L6J 5E41-800-565-3673 (FORD)www.ford.caIf yo

In some states (in the U.S.) you must directly notify Ford in writingbefore pursuing remedies under your state’s warranty laws. Ford is alsoallowed a

THE DISPUTE SETTLEMENT BOARD (U.S. ONLY)The Dispute Settlement Board is:• an independent, third-party arbitration program for warranty disputes.• avai

Board membershipThe Board consists of:• Three consumer representatives• A Ford or Lincoln Mercury dealership representativeConsumer candidates for Boa

Oral presentationsIf you would like to make an oral presentation, indicate YES to question6 on the application. While it is your right to make an oral

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADAONLY)In those cases where you continue to feel that the efforts by Ford andthe dealer to resolve a

If your vehicle must be serviced while you are traveling or living inCentral or South America, the Caribbean, or the Middle East, contact thenearest F

IN CALIFORNIA (U.S. ONLY)California Civil Code Section 1793.2(d) requires that, if a manufactureror its representative is unable to repair a motor veh

REPORTING SAFETY DEFECTS (U.S. ONLY)If you believe that your vehicle hasa defect which could cause a crashor could cause injury or death, youshould im

WASHING THE EXTERIORWash your vehicle regularly with cool or lukewarm water and a neutralPh shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is

7. Memory preset buttons: To seta station: Select frequency bandAM/FM1/FM2; tune to a station,press and hold a preset button until sound returns.8. Tu

PAINT CHIPSYour dealer has touch-up paint and sprays to match your vehicle’s color.Take your color code (printed on a sticker in the driver’s door jam

• 3.0L Vulcan engine• 3.0L Duratec engine• Never wash or rinse the engine while it is running; water in therunning engine may cause internal damage.PL

WINDOWS AND WIPER BLADESThe windshield, rear window and wiper blades should be cleanedregularly. If the wiper does not wipe properly, substances on th

INTERIORFor fabric, carpets, cloth seats, safety belts and seats equipped with sideair bags:• Remove dust and loose dirt with a vacuum cleaner.• Remov

FORD, LINCOLN AND MERCURY CAR CARE PRODUCTSYour Ford, Lincoln or Mercury dealer has many quality products availableto clean your vehicle and protect i

SERVICE RECOMMENDATIONSTo help you service your vehicle:• We highlight do-it-yourself items in the engine compartment for easylocation.• We provide a

Working with the engine on1. Set the parking brake and ensure the gearshift is securely latched in P(Park).2. Block the wheels to prevent the vehicle

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT3.0L V6 Vulcan engine1. Automatic transmission fluid dipstick2. Brake fluid reservoir3. Air filter ass

3.0L DOHC V6 Duratec engine1. Automatic transmission fluid dipstick2. Brake fluid reservoir3. Air filter assembly4. Battery5. Engine oil dipstick6. En

WINDSHIELD WASHER FLUIDAdd fluid to fill the reservoir if thelevel is low. In very cold weather, donot fill the reservoir completely.Only use a washer

2. Clock: To set the hour, press andhold the H control. When thedesired hour appears, release thecontrol.To set the minute, press and holdthe M contro

Checking and adding washer fluid for the liftgate (if equipped)The opening for the reservoir islocated on the passenger side underthe tail lamp. Refil

5. Locate and carefully remove theengine oil indicator (dipstick).6. Wipe the indicator clean. Insert the indicator fully, then remove it again.• If t

Adding engine oil1. Check the engine oil. For instructions, refer to Checking the engineoil in this chapter.2. If the engine oil level is not within t

that does not meet Ford material and design specifications, start-upengine noises or knock may be experienced.It is recommended you use the appropriat

When lifting a plastic-cased battery, excessive pressure on theend walls could cause acid to flow through the vent caps,resulting in personal injury a

• Always dispose of automotivebatteries in a responsible manner.Follow your local authorizedstandards for disposal. Call yourlocal authorized recyclin

When the engine is cold, check thelevel of the engine coolant in thereservoir.• The engine coolant should be at the “cold fill level” or within the “c

Do not put engine coolant in the windshield washer fluidcontainer. If sprayed on the windshield, engine coolant couldmake it difficult to see through

For vehicles with overflow coolant systems with a non-pressurized capon the coolant recovery system, add coolant to the coolant recoveryreservoir when

Recycled engine coolantFord Motor Company recommends the use of a recycled engine coolantproduced by Ford-approved processes in vehicles originally eq

11. Dolby威 noise reduction:Reduces tape noise and hiss whileplaying a tape, press to activate/deactivate.12. Side 1–2: Press to change tapedirection.1

• Decreased engine coolant concentrations below 40% willdecrease the corrosion protection characteristics of the enginecoolant and may cause engine da

Observe the following guidelines when handling automotive fuel:• Extinguish all smoking materialsand any open flames beforefueling your vehicle.• Alwa

Pure ethanol is the alcohol which is the intoxicating agent in liquor, beerand wine. It is distilled from the fermentation of plants such as field cor

• Keep the fuel pump nozzle in contact with the fuel container whilefilling.• DO NOT use a device that would hold the fuel pump handle in the fillposi

Choosing the right fuelUse only UNLEADED FUEL. The use of leaded fuel is prohibited by lawand could damage your vehicle.If your vehicle is a flexible

Fuel qualityMany of the world’s automakersissued the World-wide Fuel Charterthat recommends gasolinespecifications to provide improvedperformance and

Cleaner airFord endorses the use of reformulated “cleaner-burning” gasolines toimprove air quality.Running out of fuelAvoid running out of fuel becaus

Filling the tankThe advertised fuel capacity of the fuel tank on your vehicle is equal tothe rated refill capacity of the fuel tank as listed in the R

5. Follow one of the simple calculations in order to determine fueleconomy:Calculation 1: Multiply liters used by 100, then divide by totalkilometers

Maintenance• Keep tires properly inflated and use only recommended size.• Operating a vehicle with the wheels out of alignment will reduce fueleconomy

AUDIO SYSTEM WITH AM/FM STEREO/SINGLE CD PLAYER1. Clock: To set the hour, press andhold the H control. When thedesired hour appears, release thecontro

EMISSION CONTROL SYSTEMYour vehicle is equipped with various emission control components and acatalytic converter which will enable your vehicle to co

Please consult your “Warranty Guide” for complete emission warrantyinformation.Readiness for Inspection/Maintenance (I/M) testingIn some localities, i

2. While the engine idles, turn the steering wheel left and right severaltimes.3. Turn the engine off.3.0L V6 Vulcan engine4. Check the fluid level on

BRAKE FLUID RESERVOIRThe fluid level will drop slowly asthe brakes wear, and will rise whenthe brake components are replaced.Fluid levels below the “M

Low fluid levelDo not drive the vehicle if the fluidlevel is at the bottom of the dipstickand the outside temperatures areabove 10°C (50°F).Correct fl

INFORMATION ABOUT UNIFORM TIRE QUALITY GRADINGNew vehicles are fitted with tiresthat have a rating on them calledTire Quality Grades. The Qualitygrade

The traction grade assigned to this tire is based onstraight-ahead braking traction tests, and does not includeacceleration, cornering, hydroplaning o

• Four tire rotationReplacing the tiresReplace the tires when the wearband is visible through the tiretreads.When replacing full size tires, never mix

Tires that are larger or smaller than your vehicle’s original tires may alsoaffect the accuracy of your speedometer.SNOW TIRES AND CHAINSSnow tires mu

MOTORCRAFT PART NUMBERSComponent 3.0L V6 Vulcanengine3.0L FFV V6engine3.0L DOHC V6Duratec engineAir filterelement1FA-1683 FA-1683 FA-1683Fuel filter F

Seating and Safety Restraints 75Seating 75Safety restraints 79Air bags 94Child restraints 100Driving 112Starting 112Brakes 116Traction control 118Tran

6. Scan: Press to hear a briefsampling of all listenable radiostations or CD tracks. Press again tostop.7. CD: Press to play a CD. Pressagain to toggl

REFILL CAPACITIESFluid Ford PartNameApplication CapacityBrake fluid MotorcraftHighPerformanceDOT 3 MotorVehicle BrakeFluidAll Fill to line onreservoir

Fluid Ford PartNameApplication CapacityAutomatictransaxle -AX4SMotorcraftMERCON威VATF3.0L V6 Vulcanengine11.6L (12.2quarts)Windshieldwasher fluid -Fron

ItemsFord PartName orequivalentFord PartNumberFordSpecificationAutomatictransaxle (AX4Sand 4F50N1)MotorcraftMERCON威VATFXT-5-QMMERCON威VEngine oil Motor

MERCON威 and MERCON威 V type fluids are not interchangeable.DO NOT mix MERCON威 and MERCON威 V. Use of a transmissionfluid that indicates dual usage (MERC

52341Maintenance and Specifications204

IDENTIFYING YOUR VEHICLECertification labelThe National Highway Traffic SafetyAdministration Regulations requirethat a Certification label be affixedt

16. EJ (Eject): Press to eject a CD.17. AM/FM: Press to choose afrequency band (AM/FM1/FM2).CD CHANGER (IF EQUIPPED)Your CD changer is either located

5. Line up the CD with the grooveof the disc holder. Ensure that thelabel on the CD faces downwards.6. Press the disc holder until it lockssecurely in

• Tighten very loose tapes by inserting a finger or pencil into the holeand turning the hub.• Remove loose labels before inserting tapes.• Allow tapes

MANUAL HEATING AND AIR CONDITIONING SYSTEM1. Temperature selection:Controls the temperature of theairflow in the vehicle.2. Air flow selections: Contr

OPERATING TIPS• To reduce fog build up on the windshield during humid weather, placethe air flow selector in theposition.• To reduce humidity build up

ELECTRONIC AUTOMATIC TEMPERATURE CONTROL (EATC)SYSTEM (IF EQUIPPED)1. OFF: Outside air is shut out andthe fan will not operate.2. Outside temp control

6. Fan Speed: Press to manuallyincrease/decrease fan speed. Inmanual mode, the display willshowwith a bar graph to indicate fan speed. When in AUTO mo

OPERATING TIPS• To reduce fog build up on the windshield during humid weather, placethe air flow selector in the position.• To reduce humidity build u

The ignition must be in the ON position to operate the rear windowdefroster.The defroster turns off automatically after 10 minutes or when theignition

Maintenance and Specifications 165Engine compartment 167Engine oil 170Battery 173Fuel information 180Part numbers 199Refill capacities 200Lubricant sp

HEADLAMP CONTROLTurns the lamps off.Turns on the parkinglamps, instrument panel lamps,license plate lamps and tail lamps.Turns the headlamps on.Autola

High beamsPush the lever toward theinstrument panel to activate. Pullthe lever towards you to deactivate.Flash to passPull toward you slightly to acti

AIMING THE HEADLAMPSThe headlamps on your vehicle are properly aimed at the assembly plant.If your vehicle has been in an accident the alignment of yo

To see a clearer light pattern foradjusting, you may want to blockthe light from one headlamp whileadjusting the other.5. Locate the vertical adjuster

INTERIOR LAMPSREPLACING THE INTERIOR BULBSCheck the operation of all bulbs frequently.Dome lamps and map lamps• ON orD: The dome light willstay on.• D

Rear dome lamp (if equipped)The dome lamp lights when:• any door is opened with thecontrol in the middle position.• the instrument panel dimmerswitch

Function Number of bulbsTrade numberRear turn lamp (wagon) 2 3456KBackup lamp 2 921Backup lamp (wagon) 2 3156License plate lamp 2 168High-mount brake

Replacing headlamp bulbsTo remove the headlamp bulb:1. Make sure headlamp switch is inOFF position.2. Remove the bolt from theheadlamp housing.3. At t

5. Disconnect the electricalconnector from the bulb by pullingrearward.6. Remove the bulb retaining ring byrotating it counterclockwise.7. Remove the

2. Install the bulb retaining ring over the plastic base and lock the ringby rotating clockwise until it snaps into place.3. Connect the electrical co

CALIFORNIA Proposition 65 WarningWARNING: Engine exhaust, some of its constituents, andcertain vehicle components contain or emit chemicals known toth

5. Carefully pull bulb straight out ofthe socket and push in the newbulb.6. Install the bulb socket into thelamp assembly by rotating itclockwise.7. C

Replacing high-mount brakelamp bulbs — Wagon only1. Open liftgate.2. Remove two screw covers, screwsand handle from liftgate.3. Remove two screws and

7. Carefully lift the lamp assemblyaway from the liftgate.8. Remove the bulb socket byrotating it counterclockwise andpulling it out from the lampasse

3. On the underside of the spoiler,remove the two decorative screwcovers (on the LED module).4. Remove the two screws that areholding the LED module i

Sedan1. Make sure headlamp switch is inOFF position and remove twoscrews, grommets and the licenseplate lamp assembly from the trunklid.2. Carefully p

6. Install the bulb socket into the lamp assembly by rotating it clockwise.7. Install the lamp assembly on the vehicle with three nut and washerassemb

MULTI-FUNCTION LEVERWindshield wiper: Rotate the endof the control away from you toincrease the speed of the wipers;rotate towards you to decrease the

Changing the wiper blades1. Pull the wiper arm away from thevehicle. Turn the blade at an anglefrom the wiper arm. Push the lockpin manually to releas

ILLUMINATED VISOR MIRROR (IF EQUIPPED)To turn on the visor mirror lamps,lift the mirror cover. Adjust theamount of light by sliding thecontrol.AUXILIA

One touch downAllows the driver’s window to openfully without holding the controldown. Press completely down onAUTO and release quickly. Pressagain to

SAFETY AND ENVIRONMENT PROTECTIONWarning symbols in this guideHow can you reduce the risk of personal injury and prevent possibledamage to others, you

The mirror will automatically return to the normal state whenever thevehicle is placed in R (Reverse)(when the mirror is on) to ensure abright clear v

2. With the compass display turnedon, press and hold the COMP side ofthe control for no more than fiveseconds until the zone selectionnumber appears i

Heated outside mirrors (if equipped)Both mirrors are heatedautomatically to remove ice, mistand fog when the rear windowdefrost is activated.Do not re

Setting speed controlThe controls for using your speedcontrol are located on the steeringwheel for your convenience.1. Press the ON control and releas

Increasing speed while using speed controlThere are three ways to set a higherspeed:• Press and hold the SET + controluntil you get to the desiredspee

Indicator lightThis light comes on when either theSET or RES controls are pressed. Itturns off when the speed controlOFF control is pressed, the brake

If your vehicle is equipped with the column shift and a bench seat, it hasa center console in the center front seating position.The center console has

Place your wireless phone in thePocket Adapter. Dock the PocketAdapter in the Universal DockingStation. For detailed instructions,please refer to your

POSITIVE RETENTION FLOOR MATPosition the driver floor mat so thatthe eyelet is over the pointed end ofthe retention post and rotateforward to lock in.

The liftgate and liftgate window should be closed before driving yourvehicle. If not, possible damage may occur to the liftgate lift cylindersand atta

SPECIAL NOTICESEmission warrantyThe New Vehicle Limited Warranty includes Bumper-to-BumperCoverage, Safety Restraint Coverage, Corrosion Coverage, and

To reduce the risk of injuries, the fasteners for cargo area covermust be properly attached to the mounting clips on the rear trimpanels.Do not place

4. Push in the right end cap(marked RH) about1⁄4of the totallength to disengage the clutch andhold the end cap in while turningthe roller tube toward

KEYSThe key operates all locks on your vehicle. In case of loss, replacementkeys are available from your dealer.You should always carry a second key w

INTERIOR LUGGAGE COMPARTMENT RELEASEYour vehicle is equipped with a mechanical interior luggage compartmentrelease handle that provides a means of esc

REMOTE ENTRY SYSTEM (IF EQUIPPED)This device complies with part 15 of the FCC rules and with RS-210 ofIndustry Canada. Operation is subject to the fol

Locking the doors1. Press and release to lock all the doors and liftgate (wagon), turnoff the interior lamps (if they were on) and arm the anti-theft

To replace the battery:1. Twist a thin coin between the twohalves of the remote entrytransmitter near the key ring. DONOT TAKE THE FRONT PART OFTHE RE

6. Within 20 seconds press any button on the remote entry transmitter.Note: If more than 20 seconds have passed you will need to start theprocedure ov

On vehicles not equipped with the autolamps feature, only the followingitems will illuminate:• Puddle lamps• Park lamps• Tail lampsThe system will aut

When pressing the controls on the keypad, press the middle of thecontrols to ensure a good activation.Programming a personal entry codeTo create your

Special instructionsFor your added safety, your vehicle is fitted with sophisticated electroniccontrols.Please read the section Air bag in the Seating

Autolock (if equipped)This feature automatically locks all vehicle doors when the followingconditions are met:• all the doors are closed,• the engine

SECURILOCK姟 PASSIVE ANTI-THEFT SYSTEMSecuriLock娂 passive anti-theft system is an engine immobilizationsystem. This system is designed to prevent the e

Automatic armingThe vehicle is armed immediatelyafter switching the ignition to the 3(OFF) position.TheTHEFTindicator will flashevery two seconds when

1. Insert a previously programmedcoded key into the ignition.2. Turn the ignition from the 3(OFF) position to the 4 (ON)position. Keep the ignition in

Arming the systemWhen armed, this system will respond if unauthorized entry isattempted. When unauthorized entry occurs, the system will flash thehead

SEATINGNotes:Reclining the seatback can cause an occupant to slide under theseat’s safety belt, resulting in severe personal injuries in theevent of a

Using the manual lumbar support (if equipped)The lumbar control is located on thefront of the seat cushion.Turn to adjust lumbar support.Adjusting the

Adjusting the front power seat (if equipped)The control is located on the outboard side of the seat cushion.Press to raise or lower the frontportion o

Make sure that the safety belt for the rear center passenger is properlyrouted over the rear seatback.3rd seat (wagon only)The third seat faces the re

To close the seat, make sure the safety belts are properly stowed, thenlift the remote latch release and push the seat down until it latches. Pullup o

These are some of the symbols you may see on your vehicle.Vehicle Symbol GlossarySafety AlertSee Owner’s GuideFasten Safety Belt Air Bag-FrontAir Bag-

collisions, not rollovers, side-impacts, or rear-impacts unless the collisioncauses sufficient longitudinal deceleration.Driver and passenger dual-sta

Front safety belt energy management retractorsThe front safety belt energy management retractors allow webbing to bepulled out of the retractor in a g

All occupants of the vehicle, including the driver, should alwaysproperly wear their safety belts, even when an air bag (SRS) isprovided.It is extreme

2. To unfasten, push the releasebutton and remove the tongue fromthe buckle.Energy management retractorsYour vehicle has a seat belt system equipped w

How to use the automatic locking mode• Buckle the combination lap andshoulder belt.• Grasp the shoulder portion andpull downward until the entirebelt

After any vehicle collision, the seat belt system at all outboardseating positions (except driver, which has no “automatic lockingretractor” feature)

Safety belt usage sensorsThe driver and front outboard passenger safety belt buckles areequipped with sensors that detect if the safety belts are fast

Insert the tongue into the correctbuckle (the buckle closest to thedirection the tongue is comingfrom). To lengthen the belt, turn thetongue at a righ

To fasten the belt, pull the combination lap and shoulder belt from theretractor so that the shoulder belt portion of the safety belt crosses yourshou

Conditions of operationIf... Then...The driver’s safety belt is notbuckled before the ignitionswitch is turned to the ONposition...The safety belt war

Vehicle Symbol GlossaryPower WindowsFront/RearPower Window LockoutChild Safety DoorLock/UnlockInterior LuggageCompartment ReleaseSymbolPanic Alarm Eng

The following are reasons most often given for not wearing safety belts:(All statistics based on U.S. data)Reasons given... Consider...“Crashes are ra

Reasons given... Consider...“I have an air bag” Air bags offer greater protection whenused with safety belts. Frontal airbagsare not designed to infla

To reduce the risk of injury, do not deactivate/activate the BeltMinder feature while driving the vehicle.1. Turn the ignition switch to the RUN (or O

Safety belt extension assemblyIf the safety belt is too short when fully extended, there is a 20 cm (8inch) safety belt extension assembly that can be

AIR BAG SUPPLEMENTAL RESTRAINT SYSTEMThe air bag supplemental restraint system is designed to work inconjunction with the safety belts to help protect

Important supplemental restraint system precautionsAir bags DO NOT inflate slowly orgently and the risk of injury from adeploying air bag is greatest

Do not attempt to service, repair, or modify the Air BagSupplemental Restraint System or its fuses. See your Ford orLincoln Mercury dealer.The front p

How do the air bag supplemental restraints work?The air bags inflate and deflaterapidly upon activation. After air bagdeployment, it is normal to noti

Determining if the system is operationalThe supplemental restraint system uses a warning indicator in theinstrument cluster or a back-up tone to indic

All occupants of the vehicle should always wear their safety beltseven when an air bag SRS is provided.How does the side air bag system work?The side